Versions Compared

Old Version 4

changes.mady.by.user HTEK_admin

Saved on

compared with

New Version 5

changes.mady.by.user HTEK_admin

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

PDFnameHtek_IP_Phones_UC924_User_Manual_V4_4_29.pdf

Anchor
_Toc356392548
_Toc356392548
Anchor
_Ref359240935
_Ref359240935
Anchor
_Toc346281084
_Toc346281084
Anchor
_Toc347846615
_Toc347846615
Anchor
_Toc350702736
_Toc350702736
Image Added Image Added






Htek IP Phones UC924
User Manual





























Version 2.0.4.4.36
April. 2018

Anchor
_Toc509316807
_Toc509316807
Notices Information

Anchor
_Toc346281085
_Toc346281085
Anchor
_Toc347846616
_Toc347846616
Anchor
_Toc350702737
_Toc350702737
Anchor
_Toc509316808
_Toc509316808
Copyright

Anchor
_Toc347846620
_Toc347846620
Anchor
_Toc350702741
_Toc350702741
Anchor
_Toc346206964
_Toc346206964
Anchor
_Toc346281088
_Toc346281088
Copyright © 2005 - 2018 Nanjing Hanlong Technology CO., LTD. All rights reserved.
Nanjing Hanlong Technology Co., LTD. owns all the rights to modify and copy this document at any time. And all the illustrations and text in this document are copyright protected. Therefore, no parts of this document may be used or reproduced, transmitted by the third parties for any purposes without the express written permission of Nanjing Hanlong Technology CO., LTD.
When this document is made available on www.htek.com , Nanjing Hanlong Technology Co., LTD. gives its right to download and print copies of this content only for private use as a user manual. No parts shall have the right to alter, modify or use as commercial means without prior written permission from Nanjing Hanlong Technology Co., LTD.

Anchor
_Toc346281086
_Toc346281086
Anchor
_Toc347846617
_Toc347846617
Anchor
_Toc350702738
_Toc350702738
Anchor
_Toc505324906
_Toc505324906
Anchor
_Toc509316809
_Toc509316809
Safety Instructions

  • To use the Phone, please follow the instructions in this user manual.
  • Use the power adapter supplied with your phone. Other power adapters may damage the phone.
  • This phone is only for indoor use. And also avoid in high humidity, water and some other liquids.
  • Do not use the phone during thunderstorms.
  • CE
  • FCC

Anchor
_Toc391560948
_Toc391560948
Anchor
_Toc505324907
_Toc505324907
Anchor
_Toc509316810
_Toc509316810
WEEE Warning

Image Added To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Anchor
_Toc346281087
_Toc346281087
Anchor
_Toc347846619
_Toc347846619
Anchor
_Toc350702740
_Toc350702740
Anchor
_Toc505324908
_Toc505324908
Anchor
_Toc509316811
_Toc509316811
Cleaning

To clean the device, use an anti-static cloth. Please avoid cleaning liquids as they might damage the surface or internal electronics of the phone.

Anchor
_Toc505324909
_Toc505324909
Anchor
_Toc509316812
_Toc509316812
FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

















Anchor
_Toc474144990
_Toc474144990
Anchor
_Toc509316813
_Toc509316813
Summary of changes

This section describes the changes to this user manual for each release and user manual version.

Change for Release x.0.4.4.36,Manual version x.0.4.4.36

Anchor
_Toc509316403
_Toc509316403
Anchor
_Toc509316814
_Toc509316814
Major updates have occurred to the following sections:

Change for Release x.0.4.4.27,Manual version x.0.4.4.27

Major updates have occurred to the following sections:

  • UC924 supports 12 accounts

Anchor
_Toc475178282
_Toc475178282
Anchor
_Toc13627
_Toc13627
Anchor
_Toc509316815
_Toc509316815
Change for Release x.0.4.0.10,Manual version x.0.4.0.10

Major updates have occurred to the following sections:

Anchor
_Toc474144991
_Toc474144991
Anchor
_Toc475178281
_Toc475178281
Anchor
_Toc21868
_Toc21868
Anchor
_Toc509316816
_Toc509316816
Change for Release x.0.4.0,Manual version x.0.4.0

Major updates have occurred to the following sections:

  • Anchor
    OLE_LINK129
    OLE_LINK129
    Anchor
    OLE_LINK130
    OLE_LINK130
    Anchor
    OLE_LINK131
    OLE_LINK131
    Anchor
    OLE_LINK132
    OLE_LINK132
    IPv6
  • IPv4&IPv6

Anchor
_Toc509316817
_Toc509316817
Change for Release x.0.3.98.O,Manual version x.0.3.98.O

Major updates have occurred to the following sections:

Anchor
_Toc509316818
_Toc509316818
Change for Release x.0.3.98.A,Manual version x.0.3.98.A

Major updates have occurred to the following sections:

Anchor
_Toc509316819
_Toc509316819
Change for Release x.0.3.98,Manual version x.0.3.98

Major updates have occurred to the following sections:

Anchor
_Toc509316820
_Toc509316820
Change for Release x.0.3.93,Manual version x.0.3.93

Major updates have occurred to the following sections:

Anchor
_Toc509316821
_Toc509316821
Change for Release x.0.3.88,Manual version x.0.3.88

Major updates have occurred to the following sections:

Anchor
_Toc509316822
_Toc509316822
Change for Release x.0.3.72,Manual version x.0.3.72

Major updates have occurred to the following sections:

Anchor
_Toc509316823
_Toc509316823
Change for Release x.0.3.65,Manual version x.0.3.65

Major updates have occurred to the following sections:

Anchor
_Toc509316824
_Toc509316824
Change for Release x.0.3.63,Manual version x.0.3.63

Major updates have occurred to the following sections:

Anchor
_Toc509316825
_Toc509316825
Change for Release
Anchor
OLE_LINK19
OLE_LINK19
Anchor
OLE_LINK24
OLE_LINK24
x.0.3.62,Manual version x.0.3.62

Major updates have occurred to the following sections:

Anchor
_Toc509316826
_Toc509316826
Table of Content

Anchor
_Toc347846621
_Toc347846621
Anchor
_Toc346206959
_Toc346206959
Anchor
_Toc346281093
_Toc346281093
Notices Information
Copyright
Safety Instructions
WEEE Warning
Cleaning
FCC Statement
Summary of changes
Change for Release x.0.4.4.27,Manual version x.0.4.4.27
Change for Release x.0.4.0.10,Manual version x.0.4.0.10
Change for Release x.0.4.0,Manual version x.0.4.0
Change for Release x.0.3.98.O,Manual version x.0.3.98.O
Change for Release x.0.3.98.A,Manual version x.0.3.98.A
Change for Release x.0.3.98,Manual version x.0.3.98
Change for Release x.0.3.93,Manual version x.0.3.93
Change for Release x.0.3.88,Manual version x.0.3.88
Change for Release x.0.3.72,Manual version x.0.3.72
Change for Release x.0.3.65,Manual version x.0.3.65
Change for Release x.0.3.63,Manual version x.0.3.63
Change for Release x.0.3.62,Manual version x.0.3.62
Table of Content
Getting Started
Packing List
Phone Installation
1. Attach the phone stand
2. Connect the Handset and optional Headset
3. Connect the Network and Power
Initialization
Status
Registration
Idle Screen
Getting Familiar with Your Phone
Hardware Components Preview
Icon Preview
LED Instruction
Power Indicator LED
Line LED:(Line or Line Key set as Line)
BLF or BLF List Key LED Line/Line Key set as BLF)
Shared Line LED:
Other Key Led
User Interface
Line Key Function Overview
Basic Setting Configuration
General Settings
Web Login
Administrator Password
Display Mode
Language
Wallpaper
Screen Saver
Backlight
Time and Date
LED Status Setting
Key as Send
Network Setting
IPv4
IPv6
IPv4&IPv6
PC Port
Contact Setting
Local Directory
Remote Phonebook
LDAP Phonebook
Search Contact
Call History Setting
Call History
Audio Setting
Ring Tone
Volume
Voice Mail Tone
Play Hold Tone
Play Hold Tone Delay
System Settings
Dial Plan
Dial-Now Timeout
No Key Entry Timeout
Emergency Call
Label Scroll
Show Missed Calls
Auto Logout Time
Reboot in Talking
Detect IP Conflict
Redial Mode
Keypad Lock
Suppress DTMF Display
Suppress DTMF Display Delay
Check-Syn With Authenticate
Other features settings
Action URL
Softkey Layout
Programmable Key
Exp Key
Basic Call Features
Place a Call
End a Call
Redial a Call
Receive a Call
Incoming Call Show Mode
Auto Answer
Call Hold
Call Transfer
Call Conference
Call Forward
Call Return
Call Back
Call Waiting Tone
Hide Caller ID
Reject Anonymous
Call Mute
DND
Hot Line
Auto Redial
Function Key Features and Settings
Line
Speed Dial
BLF
Visual Alert for BLF Pickup
Audio Alert for BLF Pickup
BLF List
Voice Message
Direct Pickup
Group Pickup
Call Park
Intercom
Intercom Barge
DTMF
Prefix
Local Group
XML Group
LDAP
XML Browser
Broadsoft Group
Conference
Forward
Transfer
Hold
Group Listening
DND
Redial
SMS
Send SMS
Set SMS Line Key
Record
URL Record
Paging
Shared Line
Public Hold
Private Hold
Hot Desking
ACD
Zero Touch
Multicast Paging
Sending RTP Stream
Receiving RTP Stream
Upgrade
Factory Reset
Pcap Feature
System Log
Upgrade
Configuration File
Troubleshooting
Why is the phone LCD screen blank?
Why does the phone display "Network Unavailable"?
Why can't I get a dial tone?
Where to set the tone?
How to download XML Configuration?
How to Import Trusted CA certificate?
How to Import Server CA certificate?
How to use Vlan?
How to use LLDP?
How to Set LCD and Web GUI?
How to Upgrade via FTP?
How to make Ringtone?
How to use Open VPN?
Provisioning Guide on Free PBX
Redundancy Server
How to Use Auto Provision Phonebook?
All Documents
Anchor
_Toc475178470
_Toc475178470
Anchor
_Toc350702742
_Toc350702742
Anchor
OLE_LINK110
OLE_LINK110
Anchor
OLE_LINK109
OLE_LINK109
h1.
Anchor
_Toc509316827
_Toc509316827
Getting Started
Anchor
_Toc346206956
_Toc346206956
Anchor
_Toc346281090
_Toc346281090

Anchor
_Toc346206958
_Toc346206958
Anchor
_Toc346281092
_Toc346281092
Anchor
_Toc347846622
_Toc347846622
Anchor
_Toc350702743
_Toc350702743
Anchor
_Toc509316828
_Toc509316828
Packing List

The package contains the following parts, please check if all the items are not missed:

  1. The phone station

Image Added

  1. Anchor
    OLE_LINK74
    OLE_LINK74
    Anchor
    OLE_LINK75
    OLE_LINK75
    The phone stand

Image Added

  1. Handset

Anchor
OLE_LINK78
OLE_LINK78
Anchor
OLE_LINK79
OLE_LINK79
Image Added

  1. Headset cord

Image Added

  1. Power adapter

Image Added

  1. Ethernet cable

Image Added

  1. User Manual



Image Added

Anchor
_Phone_Installation
_Phone_Installation
Anchor
_Toc346206960
_Toc346206960
Anchor
_Toc346281094
_Toc346281094
Anchor
_Toc347846623
_Toc347846623
Anchor
_Toc350702744
_Toc350702744
Anchor
_Toc509316829
_Toc509316829
Phone Installation

Anchor
_Toc346206961
_Toc346206961
Anchor
_Toc346281095
_Toc346281095
Anchor
_Toc347846624
_Toc347846624
Anchor
_Toc350702745
_Toc350702745
Anchor
_Toc509316830
_Toc509316830
1. Attach the phone stand

Anchor
OLE_LINK72
OLE_LINK72
Anchor
OLE_LINK73
OLE_LINK73
Image Added

Anchor
_Toc346206962
_Toc346206962
Anchor
_Toc346281096
_Toc346281096
Anchor
_Toc347846625
_Toc347846625
Anchor
_Toc350702746
_Toc350702746
Anchor
_Toc509316831
_Toc509316831
2. Connect the Handset and optional Headset

Image Added

Anchor
_Toc346206963
_Toc346206963
Anchor
_Toc346281097
_Toc346281097
Anchor
_Toc347846626
_Toc347846626
Anchor
_Toc350702747
_Toc350702747
Anchor
_Toc509316832
_Toc509316832
3. Connect the Network and Power

Anchor
OLE_LINK80
OLE_LINK80
Anchor
OLE_LINK81
OLE_LINK81
Image Added

Anchor
_Toc347846627
_Toc347846627
Anchor
_Toc350702748
_Toc350702748
Anchor
_Toc509316833
_Toc509316833
Initialization

After your phone has been powered up, the system boots up and performs the following steps:
Automatic Phone Initialization
The phone finishes the initialization process by loading the saved configuration. The phone LCD screen will display "Booting"
Image Added
And then show "Initializing "during the initialization.
Image Added

Anchor
OLE_LINK38
OLE_LINK38
Anchor
OLE_LINK39
OLE_LINK39
The IP Phone will upgrade the firmware if there is a new firmware on your server. And the IP Phone will show "Check firmware, please waitg…" after initialization.
Image Added
Then IP Phone will show Reboot information:
Image Added
By default, the phone attempts to contact a DHCP server in your network in order to obtain its valid network settings, e.g. IP address, subnet mask, default gateway, DNS server.

Anchor
_Toc509316834
_Toc509316834
Status

You can view the system status of your phone via phone user interface or web user interface. The information of phone status includes: Information (e.g., Model, IP, MAC, Firmware, Hardware), Network (e.g., WAN Type, IP, Mask, LAN Type, Gateway, DNS …), Account (e.g., register status of accounts).
To view the phone status via phone interface:

  1. Press Menu
    Anchor
    OLE_LINK3
    OLE_LINK3
    Anchor
    OLE_LINK4
    OLE_LINK4
    →Status →Information

Image Added

  1. Press Menu →Status →Network

Image Added

  1. Press Menu →Status →Network→IPV4

Image Added

  1. Press Menu →Status →Network→IPV6

Image Added

  1. Press Menu →Status →Account(UC924 support twelve accounts)

Image Added
To view the phone status via Web interface:
Login web interface ( For How to login, please refer to Web Login)
View the information of Version, Account and Network.
Image Added

Anchor
_Toc509316835
_Toc509316835
Registration

To register via phone interface:

  1. Press Menu? Settings?Advanced Setting (default password: admin)?Accounts


  1. Select the desired account


  1. Select Enable for Account active


  1. Select the desired profile of the account.


  1. Fill the SIP User ID, Authenticate ID


  1. Fill the Password and Name (shown on LCD).


  1. Press Save to save the configuration.

Wiki Markup
!worddav76229d16159827b63c6e65c6c4e4d3d4.png|height=266,width=399!
\\
<ac:structured-macro ac:name="anchor" ac:schema-version="1" ac:macro-id="6a2acdbf-663b-4027-bc25-a4908fdf3032"><ac:parameter ac:name="">OLE_LINK32</ac:parameter></ac:structured-macro><ac:structured-macro ac:name="anchor" ac:schema-version="1" ac:macro-id="61911b3f-b559-43df-9ffa-c936c06d9b2c"><ac:parameter ac:name="">OLE_LINK33</ac:parameter></ac:structured-macro>{*}Note:*
If there is a port of sip server, you need to press "1" on the keypad, then you will find the ":".
*Additional Information:*
When the current input method is ABC/abc/2ab,
Pressing "1", you will find ", . ?:;"
Pressing "0", you will find "< > () \{\} \[\]"
Pressing "*", you will find "*/"! @$"
Pressing "#", you will find "#'%&*|"
\\
*To register via Web interface:*
\\

  1. Login Web interface and Click Profile?Basic.

Image Added

  1. Fill the Primary SIP Server and other profile information.


  1. Select the SIP Transport.


  1. Click Image Added to save the configuration.


  1. Click Account?Basic.

Image Added

  1. Select Yes for Account Active.


  1. Select the desired Profile.


  1. Fill the SIP User ID, Authenticate ID, Authenticate Password and other account information.


  1. Click Image Added to save the configuration.


Note:

  1. All fields with *** must be filled. If changed, it requires a phone restart.
  2. Account Status says the account registered successfully or not.



Anchor
_Toc509316836
_Toc509316836
Idle Screen

Image Added

Anchor
OLE_LINK84
OLE_LINK84
Anchor
OLE_LINK85
OLE_LINK85
Name

Description

1. Date & Time

It is the area that displays the current set date and time of the phone.

2. Notice

It is the area to display the phone's notifications such as missed calls, SMS, do not disturb mode and many more. For more info, see Icon Preview.

3. Line Keys

This area shows the line key labels. The current account is highlighted. you can switch the account by pressing right or left navigation key. The Line keys are also can be used as other function keys. For more information you can refer to
Line Keys

4. Soft Key

This area shows the soft key labels. The default soft key labels are
"History", "Directory", "DND" and "Menu". For more info, see Programmable Key

5. DSS key

The Line keys can be used for other function keys(e.g.: BLF)

Anchor
OLE_LINK82
OLE_LINK82
Anchor
OLE_LINK83
OLE_LINK83
6.Multipage key

UC924 support 28 keys,you can configure different types.you can view and use these keys by pressing the multipage key.

7. Wallpaper

This shows the current wallpaper picture. You can also change it.
For more information you can refer to Wallpaper.



Anchor
_Toc347846631
_Toc347846631
Anchor
_Toc350702749
_Toc350702749
Anchor
_Toc509316837
_Toc509316837
Getting Familiar with Your Phone

Anchor
_Toc347846632
_Toc347846632
Anchor
_Toc350702750
_Toc350702750
Anchor
OLE_LINK119
OLE_LINK119
Anchor
OLE_LINK120
OLE_LINK120
Anchor
_Toc509316838
_Toc509316838
Hardware Components Preview

Image Added

Item

Description

LCD screen

To Presentation all information about the date& time, accounts, soft keys, messages, calls and other some information.

Power Indicator LED

To indicate the power status

Line keys

The phone supported up to 4 accounts

  1. Steady green: idle interface, during a call..
  2. Blink red: a call incoming

Soft keys

Labels automatically to identity their context-sensitive features.

Navigation keys

Image Added 1. OK.

Image Added Up arrow key: To move up of the selection shows on the screen.
Image Added Right arrow key: To move right of the selection
shows on the screen.
Image Added Left arrow key: To move left of the selection shows on the screen.
Down arrow key: To move down of the selection shows on the screen.
1. To return to idle screen.
2. To cancel the information or call on the screen.
Image AddedImage Added

Mute key

Image Added 1. To mute the voice during the call (Red light).
2. To un-mute the call.

Conference

Image Added To place a conference call

Line Keys

To be configured as different function as:

  1. Line
  2. Speed Dial
  3. BLF
  4. BLF List
  5. Voice Mail
  6. Direct Pickup
  7. Group Pickup
  8. Call Park
  9. Intercom
  10. DTMF
  11. Prefix
  12. Local Group
  13. XML Group
  14. XML Browser
  15. LDAP
  16. Network Directories
  17. Conference
  18. Forward
  19. Transfer
  20. Hold
  21. DND
  22. Redial
  23. Call Return
  24. SMS
  25. Record
  26. URL Record
  27. Paging
  28. Group Listening
  29. Public Hold
  30. Private Hold
  31. Hot Desking
  32. ACD
  33. Zero Touch
  34. URL
  35. Network Group
  36. Multicast Paging
  37. Group Call Park
  38. CallPark Retrieve
  39. Pull Call
  40. Shared Line

    The LED lights status when set as Shared line:
    Stay green: Idle
    Stay red: Busy
    Blinked green: Ring Back
    Blinked red: A call incoming
    Steady orange: During a call
    Blinked orange: Public Hold
    Blinked green: Private Hold
    Light Drown: Unregistered
  41. Broadsoft Group

Speaker

Image Added Press this button to place a call in hands-free mode.

Redial

Image Added
To dial the previous dialed number.
To act as send key.

Volume

Image Added
To decrease the volume.
Image Added
To increase the volume.

Hold

Image Added To hold or to resume a call during a conversation.

Transfer

Image Added
To transfer a call to a third party.
To enable or disable Forward feature during the idle page.

Alphanumeric keypad

To enter the phone numbers, letters and so on.

Message

Image Added To indicator the New message, and press to read.

Headset

Image Added To indicate that the phone is or not in Headset mode.


Anchor
_Icon_Preview
_Icon_Preview
Anchor
_Toc346206957
_Toc346206957
Anchor
_Toc346281091
_Toc346281091
Anchor
_Toc347846633
_Toc347846633
Anchor
_Toc350702751
_Toc350702751
Anchor
_Toc509316839
_Toc509316839
Icon Preview

Anchor
_Memory_Key_Function_Overview
_Memory_Key_Function_Overview
Icon

Description

Image Added

Network down

Image Added

Line(Registered succeed)

Image Added

Line (Unregistered)

Image AddedImage Added

Line(Ringing)

Image Added

Speed Dial

Image Added

BLF

Image Added

BLF(Ringing)

Image Added

BLF(Talking)

Image Added

Speakerphone mode

Image Added

Handset mode

Image Added

Headset mode

Image Added

Voice messages


Image Added

Text message

Image Added

Mute

Image Added

Do Not Disturb

Image Added

Volume is 0

Image Added

SRTP

Image Added

Hold

Image Added

Dialed calls

Image Added

Received calls

Image Added

Missed calls

Image Added

Forward calls

Image Added

Conference

Image Added

Keypad locked

Image Added

Pick up

Image Added

Call Park


Image Added

Intercom/Paging

Image Added

DTMF

Image Added

Prefix

Image Added

XML Group

Image Added

Local Group

Image Added

XML Browser

Image Added

LDAP

Image Added

Broadsoft Group

Image Added

Conference

Image Added

Forward

Image Added

Transfer

Image Added

Hold

Image Added

Redial

Image Added

Call Return

Image Added

Record


Image Added

Stop Recording

Image Added

Group Listening

Image Added

Shared Line

Image Added

Other Functions


Anchor
_Toc509316840
_Toc509316840
LED Instruction

This part mainly instructs the LED status. The Power LED Status describe on the premise that the LED setting all set as Yes. For LED status setting, please refer to: LED Status Setting

Anchor
_Power_Indicator_LED
_Power_Indicator_LED
Anchor
_Toc509316841
_Toc509316841
Power Indicator LED

LED Status

Description

Blinked green

Ringing or have missed call

Steady Green

Idle status(Power on)

Off

Powered off.


Anchor
_Toc509316842
_Toc509316842
Line LED:(Line or Line Key set as Line)

LED Status

Description

Steady Green

Hold

Steady Green

Off hook or during a conversation.

Blinked red

Ringing.

Off

Idle status


Anchor
_Toc509316843
_Toc509316843
BLF or BLF List Key LED (sad) Line/Line Key set as BLF)

LED Status

Description

Steady Green

Idle status for the monitored line

Steady Red

The monitored line is calling or during a call

Blinked red

The monitored line is ringing.

Off

All other unknown status


Anchor
OLE_LINK50
OLE_LINK50
Anchor
OLE_LINK51
OLE_LINK51
Anchor
_Toc509316844
_Toc509316844
Shared Line LED:

Anchor
OLE_LINK68
OLE_LINK68
Anchor
OLE_LINK69
OLE_LINK69
LED Status

Description

off

Idle status

Anchor
OLE_LINK52
OLE_LINK52
Anchor
OLE_LINK53
OLE_LINK53
Stay green

a member of the SCA group in off-hook status

Anchor
OLE_LINK54
OLE_LINK54
Anchor
OLE_LINK55
OLE_LINK55
Stay red

Other member of the SCA group's led status when a member of the SCA group in off-hook status

Blinked green every 500ms

a member of the SCA group in Private hold status.

Anchor
OLE_LINK58
OLE_LINK58
Anchor
OLE_LINK59
OLE_LINK59
Stay red

Other member of the SCA group's led status when a member of the SCA group in Private hold status

Blinked green every 500ms

a member of the SCA group in public hold status

Anchor
OLE_LINK60
OLE_LINK60
Anchor
OLE_LINK61
OLE_LINK61
Blinked red every 500ms

Other member of the SCA group's led status when a member of the SCA group in public hold status

Blinked green every 500ms

a member of the SCA group in

Anchor
OLE_LINK56
OLE_LINK56
Anchor
OLE_LINK57
OLE_LINK57
progressing status

Anchor
OLE_LINK62
OLE_LINK62
Anchor
OLE_LINK63
OLE_LINK63
Stay red

Other member of the SCA group's led status when a member of the SCA group in progressing status

Blinked red every 100ms

Alerting

Stay green

a member of the SCA group in active status when there is an incoming call designated for the SCA group

Stay red

Other member of the SCA group's led status when a member of the SCA group in active status


Anchor
_Toc509316845
_Toc509316845
Other Key Led

Key

Description

Headset Key

When using in headset mode, the led is steady green or the LED is off.

Message Key

Blinked green when there is a new message or the LED is off.

Mute Key

Red when the mute the call, or the LED is off.

Anchor
_Info_Key_Instruction
_Info_Key_Instruction

Anchor
_Toc509316846
_Toc509316846
User Interface

There are two ways to customize specific configurations on your IP phone:

  • ? The user interface on the IP phone
  • ? The user interface in a web browser on your PC


The hardware components keypad and LCD screen constitute the phone user interface, which allows the user to execute all call operation tasks and basic configuration changes directly on the phone. In addition, you can use the web user interface to access all configuration settings. In many instances, it is possible to use both the phone user interface and the web user interface to operate the phone and change settings. However, in some instances, it is only possible to use the phone or the web user interface.
Phone Interface Overview

Option

 

Status

Information

 

Network

 

Accounts

Features

Call Forward

 

Function Keys (Line and Line Key setting)
More Key see Line Key Overview

 

Key as Send

 

Hot Line

 

Anonymous Call

 

DND

 

History Setting

Directory

All Contacts

 

Local Contacts

 

BlackList

History

Local History

 

Network CallLog

Message

Voice Mail View and Set.

 

Text Message View and Set.

Basic Setting

Language

 

Time & Date

 

Time & Date Format

 

DHCP Time

 

Ring Tone

 

Headset

 

Font Size

Advanced Setting

Accounts

 

Network

 

Phone Setting

 

Auto Provision

Display

Display Mode

 

Wallpaper

 

Screensaver

Others

Factory Function

 

System Restart

 

Device Reboot

 

Pcap Feature


Anchor
_Memory_Key_Function_Overview_1
_Memory_Key_Function_Overview_1
Anchor
_Toc509316847
_Toc509316847
Line Key Function Overview

Line

Speed Dial

BLF

BLF List

Voice Mail

Direct Pickup

Group Pickup

Call Park

Intercom

DTMF

Prefix

Local Group

XML Group

XML Browser

LDAP

Network Directories

Conference

Forward

Transfer

Hold

DND

Redial

Call Return

SMS

Record

URL Record

Paging

Group Listening

Public Hold

Private Hold

Hot Desking

ACD

Zero Touch

URL

Network Group

Multicast Paging

Group Call Park

CallPark Retrieve

Pull Call

Shared Line

Broadsoft Group


Anchor
_Toc509047835
_Toc509047835
Anchor
_Toc509316848
_Toc509316848
Basic Setting Configuration

This part will mainly introduce the basic configuration as the Time, Language, and Volume…

Anchor
_Web_Login
_Web_Login
Anchor
_Toc475004847
_Toc475004847
Anchor
_Toc509047836
_Toc509047836
Anchor
_Toc509316849
_Toc509316849
General Settings

Anchor
_Web_Login_1
_Web_Login_1
Anchor
_Toc375056491
_Toc375056491
Anchor
_Toc475004848
_Toc475004848
Anchor
_Toc509047837
_Toc509047837
Anchor
_Toc509316850
_Toc509316850
Web Login

  1. Get the IP address: Press Menu →Status →Information.

Image Added

  1. Input the IP Address in the web browser.


  1. Input the user name (default is admin), password (default is admin).


  1. Login successfully.

Image Added

Note:
The PC and phone should be in the same segment.
When registering the accounts in web and the server port is not "5060", the"SIP Server" should be set as "SIP Server's IP address: server port.", for example, "192.168.0.122: 5090".


Anchor
_Toc375056492
_Toc375056492
Anchor
_Toc475004849
_Toc475004849
Anchor
_Toc509047838
_Toc509047838
Anchor
_Toc509316851
_Toc509316851
Administrator Password

The password is mainly used for login the Web interface or set the Advanced Setting through Phone interface. And the default password of the administrator is: admin
To change to password via Phone Interface

  1. Press Menu → Settings → Advanced Setting → password (default admin) →Phone Setting → Set Password


  1. Enter the current PWD (password), new password and confirm the new password.
  2. Press Save soft key or Image Added to save the new password.

Image Added
To change to password via Web Interface

  1. Management → Password


  1. Fill the value


  1. Click Image Added to save the configuration.

Image Added

Note:
When you use the Web interface: user name: admin password: admin(default)

Anchor
_Toc509047839
_Toc509047839
Anchor
_Toc509316852
_Toc509316852
Display Mode

This phone support two Display mode: Text and Icon.
Icon Mode: all Items are shown same as the main with Icon.
Text Mode: Only the 8 main items will be shown as icon, and others all text description.
To Configure Display mode via Phone interface:

  1. Press Menu? Display?Display Mode


  1. Select Text or Icon


  1. Press Save soft key to save the configuration.


To Configure Display mode via Web interface:

  1. Login Web interface, and click Setting? Preference

Image Added

  1. Select Icon Mode or Text Mode for the Display mode


  1. Click Image Added to save the configuration.

Anchor
_Toc509047840
_Toc509047840
Anchor
_Toc509316853
_Toc509316853
Language

The default Phone interface language is English.
To change the language via Phone interface

  1. Press Menu → Settings → Basic Setting → Language.

Image Added
Image Added
2.Press Image Added or Save soft key to save the configuration.
Image Added
To change the language via Web Interface

  1. Setting → Preference →Web Language & LCD Language


  1. Select the necessary one.


  1. Press Image Added to save the configuration.

Image Added

Note:
All languages may not be available for selection. The available languages depend on the language packs currently loaded to the IP phone.


Anchor
_Toc509047841
_Toc509047841
Anchor
_Toc509316854
_Toc509316854
Wallpaper

To change wallpaper, go by the following steps:
To change the wallpaper via Phone interface:

  1. To press Menu → Display → Wallpaper
  2. Press Image Added and Image Added or press Switch soft key to display the different pictures.
  3. Press Image Added or Save soft key to save the selected picture as the wallpaper.

Image Added
To change the wallpaper via Web interface:

  1. Click Setting?Preference


  1. Select the desired wallpaper picture to upload.


  1. Click Image Added to save the setting.

Image Added
To delete the wallpaper via Web interface:

  1. Click Setting?Preference
  2. Select the desired wallpaper to delete.
  3. Click Image Added to save the setting.

Image Added
Note:
System wallpaper (Wallpaper1-Wallpaper6) cannot be deleted and only color IP Phones support uploading wallpaper.

Anchor
_Toc509047842
_Toc509047842
Anchor
_Toc509316855
_Toc509316855
Screen Saver

There are three types of screen saver: Time & Logo, Photo Switch and Static Photo.
Time & Logo: When the screensaver works, it will show Time and logo in turns.
Photo Switch: All screensaver pictures display one by one.
Static Photo: Only the selected picture will display as screensaver.
Text logo: It works with the Time & Logo, when enter the value, it will display the time and the entered value in turns.
To enable screen saver via Phone interface:

  1. To press Menu → Display → Screensaver...
  2. Press Image Added and Image Added or press Switch soft key to Choose the Time-out as 1 min or 2/5/10/30 minute, then press the Save button.

Image Added

  1. Enter the Screensaver Type to choose one of the type: Time & Logo, Photo Switch and Static Photo

Image Added

  1. Press Image Added or Save soft key to save the selected configuration.


To disable screen saver via Phone interface

  1. To press Menu → Display → Screensaver...
  2. Press Image Added and Image Added or press Switch soft key to Choose the Time-out as off.
  3. Press Image Added or Save soft key to save the selected configuration.

Image Added
To upload screen saver via Web interface:

  1. Setting → Preference


  1. Choose the picture wanted to use as screen saver


  1. Click Image Added to save the upload picture

Image Added
To delete upload screen saver phone via Web interface:

  1. Setting → Preference


  1. Select the photo that to delete.


  1. Click Image Added to delete the photo.

Image Added

Note:
System Screen Photo (ScreenSaver1-ScreenSaver3) cannot be deleted and only color IP Phones support upload screensaver.


To custom text logo via Web interface:

  1. Click Setting?Preference.


  1. Choose the Time-out as 1 min or 2/5/10/30 minute.


  1. Enter the desired value in the Text Logo field.


  1. Click Image Added to save the configuration.

Image Added
To wake up screen saver via Web interface:
1. Setting → Preference
2. Choose Dial First Digit: Screensaver Wakes up or Screensaver Wakes up and Dial
3. Click Image Added to save the configuration.
Image Added

Note:

  1. The upload Photo size should be less than 2MB, name length should be less than 48 characters, and the File name should be letters, numbers or underline '_' and photo number should be less than 9.
  2. The default screensaver photos cannot be deleted.
  3. You can only upload screen photos in format of '.bmp' and '.jpg'.

Anchor
_Toc509047843
_Toc509047843
Anchor
_Toc509051151
_Toc509051151
Anchor
_Toc509316856
_Toc509316856
Backlight

To set Backlight via Web interface:

  1. Click Setting?Preference


  1. Enter the time for Backlight time (In seconds).

The default is 0, which means Backlight is always on.

  1. Click Image Added to save the configuration.

Image Added

Note:
Backlight Time refers to the time into the backlight


Anchor
_Toc509047844
_Toc509047844
Anchor
_Toc509316857
_Toc509316857
Time and Date

Time and date is displayed on the idle page, and it can be set automatically by SNTP server or manually by manual setting.
To configure the time and Date by SNTP setting via Phone interface

  1. To press Menu → Settings → Basic Setting → Time & Date → SNTP Settings
  2. Press Image Added or Image Added to change the Time zone.
  3. Fill the NTP Server1, NTP Server2, and select the mode of Daylight Saving.
  4. Press Image Added or Save soft key to save the configuration.

Image Added
To configure time and date manually via Phone interface

  1. To press Menu → Settings → Basic Setting → Time & Date → Manual
  2. Press Image Added and Image Added or change the right time, or you can input the right time.
  3. Press Image Added or Save soft key to save the configuration.

Image Added
To configure the Time & Date Format via Phone interface

  1. Press Menu → Settings → Basic Setting → Time & Date Format
  2. Press Image Added and Image Added to change between 12 Hour or 24 Hour time display.
  3. Press Image Added and Image Added to change date display format among Y-M-D(year-month-day), M-D-Y(month-day-year), D-M-Y(day-month-year).
  4. Press Image Added or Save soft key to save the configuration.

Image Added
To configure the DHCP time via Phone interface

  1. To press Menu → Settings → Basic Setting → DHCP Time
  2. Press Image Added and Image Added to change between Disable and Enable.
  3. Press Image Added or Save soft key to save the configuration.

Image Added
To configure the DHCP Option 100

  1. To press Menu → Settings → Date & Time → DHCP Option 100


  1. Select Yes for the DHCP SIP Server
  2. Click Image Added to save the configuration

Image Added
To configure the NTP Server by Web interface

  1. Login web page.

Login name: admin, password: admin(default)

  1. Setting → Date & Time →NTP Server


  1. Fill the value in the blank.
  2. Click Image Added to save the configuration.

Image Added
To change the Time Zone and Date Display Format via Web interface

  1. Setting → Date &Time
  2. Select the necessary one.
  3. Press Image Added to save the configuration.

Image Added
To change the SIP Date Override Time via Web interface

  1. Setting → Date &Time→ SIP Date Override Time
  2. Select Yes or No for SIP Date Override Time .
  3. Click Image Added to save the configuration.

Image Added

Anchor
OLE_LINK117
OLE_LINK117
Anchor
OLE_LINK118
OLE_LINK118
To change the Account via Web interface

  1. Setting → Date &Time →Account.


  1. Select desired Account.


  1. Click Image Added to save the configuration.

Image Added
To change the Daylight Saving Time via Web interface

  1. Setting → Date &Time→ Daylight Saving Time


  1. Select Disable or Enable or Auto for Daylight Saving Time.


  1. Click Image Added to save the configuration.

Image Added

Note:
If the IP Phone cannot obtain the time and date from the Simple Network Time Protocol (SNTP) server, please contact your system administrator for more information.

Anchor
_Toc347846636
_Toc347846636
Anchor
_Toc350702754
_Toc350702754

Daylight Saving Time
Daylight Saving Time (DST) is the practice of temporary advancing clocks during the summertime so that evenings have more daylight and mornings have less. Typically, clocks are adjusted forward one hour at the start of spring and backward in autumn. Many countries have used the DST at various times, details vary by location. The DST can be adjusted automatically from the time zone configuration. Typically, there is no need to change this setting.

Anchor
_LED_Status_Setting_1
_LED_Status_Setting_1
Anchor
_Toc509047845
_Toc509047845
Anchor
_Toc509316858
_Toc509316858
LED Status Setting

The LED Status setting mainly defines the power indicator LED.
To configure LED Status via Web interface:

  1. Click Setting?Preference


  1. Select Yes or No for Power Status, Ringing Status, Miss Calls Status and Voice Message Status.


  1. Click Image Added for the setting.

For the LED status description, see: LED Instruction Power Indicator LED
Image Added

Anchor
_Toc509047846
_Toc509047846
Anchor
_Toc509316859
_Toc509316859
Key as Send

To configure Key as Send via Phone interface:

  1. Press Menu →Features → Key as Send


  1. Press Image Added and Image Added key to select the enable choice.


  1. Press Image Added or Save soft key to save the configuration

Image Added
To cancel # Key as Send via Phone interface:

  1. Press Menu →Features → Key as Send


  1. Press Image Added and Image Added key to select the disable choice.


  1. Press Image Added or Save soft key to save the configuration

Anchor
_Toc509047847
_Toc509047847
Anchor
_Toc509316860
_Toc509316860
Network Setting

Anchor
OLE_LINK40
OLE_LINK40
Anchor
OLE_LINK41
OLE_LINK41
Htek IP Phone supports IPv4?IPv6?IPv4&IPv6.They have three modes of Network: DHCP, Static, and PPPoE. The default mode is DHCP, it will obtain IP address and other information automatically.
If your phone cannot contact a DHCP server for any reason, you need to configure a static IP address manually.
When switch DHCP, Static IP and PPPoE to each other, or change the Static IP on Web interface , it will show the warning of restart as following.
Image Added

Anchor
_Toc509047848
_Toc509047848
Anchor
_Toc509316861
_Toc509316861
IPv4

If you set IP Mode to IPv4, IP phone will use IPv4 address. IPv4 has three network modes: DHCP, Static, and PPPoE
To configure IPv4 via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?WAN Port ?IP Port Mode.
  2. Press Image Added or Image Added to change the IP Port Mode..
  3. Press Image Added or Save soft key to save the configuration.

Image Added
To configure IPv4 via Web interface:

  1. Click Network?Basic? Internet Port


  1. Select IPv4 for Internet Port


  1. Click Image Added for the setting.

Image Added
To configure DHCP via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?WAN Port ?IPv4?DHCP mode.


  1. Click Save and restart the phone.


To configure a static IP address via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?WAN Port ?IPv4 ?Static mode.


  1. Enter the parameters: IP, Netmask, Gateway, Pri.DNS(primary DNS), Sec.DNS (secondary DNS) in the corresponding fields.

Image Added

  1. Click Save and restart the phone.

Image Added

  1. Press the OK soft key to accept the change or the Cancel soft key to cancel. If you are using an xDSL modem, you can connect your phone to the Internet via PPPoE mode. You can set a WAN port to be a PPPoE port. The PPPoE port will perform a PPP negotiation to obtain the IP address. Contact your system administrator for the PPPoE user name and password.


To configure PPPoE via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?WAN Port ?PPPoE mode.


  1. Enter the User ID and password


  1. Click Save and restart the phone.

Image Added
To configure Network via Web interface:

  1. Click Network?Basic?IPv4 setting


  1. Select the desired Type: DHCP, Static or PPPoE


  1. Fill the necessary information.


  1. Click Image Added and restart the phone.

Image Added

Anchor
_IPv6
_IPv6
Anchor
_Toc475004860
_Toc475004860
Anchor
_Toc509047849
_Toc509047849
Anchor
_Toc509316862
_Toc509316862
IPv6

If you set IP Mode to IPv6, IP phone will use IPv6 address. IPv6 has two network modes: DHCP, Static
To configure IPv6 via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?WAN Port ?IP Port Mode.
  2. Press Image Added or Image Added to change the IP Port Mode..
  3. Press Image Added or Save soft key to save the configuration.

Image Added
To configure IPv6 via Web interface:

  1. Click Network?Basic? Internet Port


  1. Select IPv6 for Internet Port


  1. Click Image Added for the setting.

Image Added
To configure DHCP via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?WAN Port IPv6?DHCP mode.


  1. Click Save and restart the phone.


To configure a static IP address via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?WAN Port ?IPv6 ?Static mode.


  1. Enter the parameters: IP, IPV6 Prefix, Gateway, Pri.DNS(primary DNS), Sec.DNS (secondary DNS) in the corresponding fields.

Image Added

  1. Click OK and restart the phone.

Image Added
To configure Network via Web interface:

  1. Click Network?Basic?IPv6 setting


  1. Select the desired Type: DHCP, Static


  1. Fill required fields.


  1. Click Image Added and restart the phone.

Image Added

Anchor
_IPv4&IPv6
_IPv4&IPv6
Anchor
_Toc475004861
_Toc475004861
Anchor
_Toc509047850
_Toc509047850
Anchor
_Toc509316863
_Toc509316863
IPv4&IPv6

If you set IP Mode to IPv4&IPv6, IP phone will support both IPv4 and IPv6 address. The settings of DHCP, Static, and PPPoE are same as above.
To configure IPv4&IPv6 via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?WAN Port ?IP Port Mode.
  2. Press Image Added or Image Added to change the IP Port Mode..
  3. Press Image Added or Save soft key to save the configuration.

Image Added
To configure IPv4&IPv6 via Web interface:

  1. Click Network?Basic? Internet Port


  1. Select IPv4&IPv6 for Internet Port


  1. Click Image Added for the setting.

Image Added

Note:
Wrong network parameters may result in inaccessibility of your phone and may also have an impact on your network performance. For more information about these parameters, contact your system administrator.


Anchor
_Toc475004862
_Toc475004862
Anchor
_Toc509047851
_Toc509047851
Anchor
_Toc509316864
_Toc509316864
PC Port

Three modes for PC port: bridge, connect to Expansion Module and router.
To configure PC Bridge via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?PC Port ?Bridge mode.


  1. Click Save.


  1. Click the OK button, then the phone will reboot.


To configure PC router via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?PC Port ?Router mode.


  1. Enter the IP, Netmask and DHCP server


  1. Click Save.


  1. Click the OK button, then the phone will reboot.


To configure PC, Connect to Expansion Module via Phone interface:

  1. Press Menu?Settings?Advanced Setting (password: admin) ?Network?PC Port ? Connect to Module.


  1. Click Save.


  1. Click the OK button, then the phone will reboot


To configure Bridge via Web interface:

  1. Click Network?PC Port


  1. Select As Bridge


  1. Click Image Added and the phone will reboot automatically

Image Added
To configure Router via Web interface:

  1. Click Network? PC Port


  1. Select As Router


  1. Fill the IP address and other necessary information.


  1. Click Image Added and the phone will reboot automatically

Image Added
To configure PC, Connect to Expansion Module via Web interface:

  1. Click Network? PC Port
  2. Select Connect to Expansion Module
  3. Click Image Added and the phone will reboot automatically

Image Added

Anchor
_Toc509047852
_Toc509047852
Anchor
_Toc509316865
_Toc509316865
Contact Setting

This section provides the operating instructions for managing contacts. The topics include:

  • Local Directory
  • Remote Phonebook
  • LDAP
  • Search Contact

Anchor
_Toc509047853
_Toc509047853
Anchor
_Toc509316866
_Toc509316866
Local Directory

In the directory, you can add or delete your friends, business partner or anyone others' phone No., so you will not forget their number. Or put some anonymous phone No. in the blacklist to prevent from being disturbed. The local Directory can add up to 1000 contacts.
A. To add contacts list into local directory
To add contacts manually via Phone interface

  1. Press Menu → Directory → Local Contacts


  1. Press Add soft key.


  1. Enter the necessary information as Name, Phone number…
  2. Press Save soft key or Image Added to add the contacts successfully.

Image Added
To add contacts from history via Phone interface:

  1. Press History soft key or press Menu → History → Local History
  2. Press Image Added and Image Added to select the targeted one. (Press Image Added and Image Added switched among the All Calls, Missed Calls, Received Calls, Dialed Calls and Forwarded Calls).


  1. Press Option soft key → Add to Contacts


  1. Edit the necessary information as Name, Phone number…
  2. Press Save soft key or Image Added to add the contacts successfully.

Image Added
To add contacts via Web interface:

  1. Click Directory?Directory


  1. Enter the name, number and some other information.


  1. Press Image Added and then press Image Added button.

Image Added
B: To add contacts into blacklist
To add blacklist manually via Phone interface:

  1. Press Menu → Directory → BlackList
  2. Press Group soft key.
  3. Press Add soft key.
  4. Enter the Name and select the Ring Tone.
  5. Press Save soft key or Image Added to add the Group successfully.
  6. Enter the added Group, then press Add soft key.
  7. Enter the necessary information as Name, Phone number…
  8. Press Save soft key or Image Added to add the contacts successfully.


To add blacklist from history via Phone interface:

  1. Press History soft key or press Menu → History → Local History
  2. Press Image Added and Image Added to select the targeted one.
  3. Press Option soft key → Add to Blacklist
  4. Edit the necessary information as Name, Phone number…
  5. Press Save soft key or Image Added to add successfully.

Image Added
Upload Contacts photo via Web interface:

  1. Click Directory and select the desired contact.


  1. Click Choose file to select the photo for the contact


  1. Click Image Added to upload the photo.

Image Added
When you place a call from the contact, the phone idle screen will show the contact photo.
Image Added
Contacts photo server
The contact photo server allows you to configure the contact's photo by modifying the xml file instead of uploading it on a web page.
Image Added
First fill in the server path ( e.g. http://192.168.1.18/photo/ ) .
Then, fill in the file name in the quotes for the field photoDefault = "", ( e.g. photoDefault = "htek.jpg" ).
Finally, import the xml file to the phone.
Image Added
You can get the xml file through the export function.

Note:
The format of the photo supported is .jpg or .bmp
Photo size should be less than 2MB, name length should be less than 48 characters.


To import or export the contact list
You can manage your phone's local directory via phone or web user interface. But you can only import or export the contact list via Web interface.
To import an XML file of contact list via Web interface:

  1. Click on Directory → Directory


  1. Click Choose file to select a contact list file (file format must be .xml) from your local system.


  1. Click Import XML to import the contact list.


To export an XML file of contact list via Web interface:

  1. Click on Directory → Directory


  1. Click Export XML to export the contact list.


To import a CSV file of contact list via Web interface:

  1. Click on Directory → Directory


  1. Click Choose file to select a contact list file (file format must be .csv) from your local system.


  1. Click Import Csv to import the contact list.


To export a CSV file of contact list via Web interface:

  1. Click on Directory → Directory
  2. Click Export Csv to export the contact list.

Image Added

Note:
If the xml file and CSV file have more than 1000 contacts, the phone will only upload 1000 contacts.


Anchor
_Toc509047854
_Toc509047854
Anchor
_Toc509316867
_Toc509316867
Remote Phonebook

To set Remote Phonebook via Web interface:

  1. Login the Web interface and click Directory?Remote Phone Book


  1. Fill the path of the remote file in the Phone Book URL field.

For example, http://192.168.0.106/Phonebook/Remote_Phonebook/remotephonebook.xml

  1. Fill the Name and then click Image Added to save the configuration.

Image Added
To check the contacts via Phone interface:
Press Directory?Left Button?Left Button, and you can see the item you set, press Update and then enter you will find the detail.
For More detail, please refer to: www.htek.com.

Note:
Every remote phonebook, only supports 1000 contacts.

Anchor
_Toc509047855
_Toc509047855
Anchor
_Toc509316868
_Toc509316868
LDAP Phonebook

When use the LDAP feature, you can get the LDAP Phonebook directly.
To configure LDAP via Web interface:

  1. Login Web interface and click Directory?LDAP
  2. Fill the LDAP Name Filter:
    1. This parameter specifies the name attributes for LDAP searching. The "%" symbol in the filter stands for the entering string used as the prefix of the filter condition.
    2. For example, (cn=%), when the name prefix of the cn of the contact record matches the search criteria, the record will be displayed on the IP PHONE LCD.
  3. Fill LDAP Number Filter:

This parameter specifies the number attributes for LDAP searching.

  1. Fill Server Address: Fill the domain name or IP address of the LDAP Server.

For example: 192.168.0.9

  1. Port (the port of the LDAP Server), Base, User Name, Password
  2. Max.Hits(1-32000): the maximum number of the search results to be returned by the LDAP server.
  3. LDAP Display Name: the display name of the contact record displayed on the LCD screen.
  4. Fill the relative value and then click Image Added to save the settings.

Following is the example screenshot for the configuration.
Image Added
To Configure LDAP Key
To configure LDAP Key via Web interface:

  1. Click Function Keys?Line Key? choose Line Key 2(for example)


  1. Select LDAP in the Type field.


  1. Click Image Added to save the configuration.

Image Added
To Configure LDAP Key via Phone interface:

  1. Press Menu?Features?Function Keys?Line Keys as Function Keys?Line Key 2


  1. Select LDAP in the Type field


  1. Press Save or OK key to save the configuration.

When press the LDAP Key, the LCD will display as following:
Image Added
For More detail, please refer to www.htek.com

Anchor
_Toc509047856
_Toc509047856
Anchor
_Toc509316869
_Toc509316869
Search Contact

You can search contact in all contacts, local contacts, remote contacts and LDAP contact.
To search contact in all contacts:

  1. Click the Directory soft key on Idle interface.
  2. Click the More soft key, then you can see the Search soft key
  3. Click the Search soft key, you can enter the desired part of name or part of number.
  4. With the search content to match the contact will be automatically displayed on the LCD within 5 seconds.

Image Added
To search contact in Local contacts:

  1. Click the Directory soft key on Idle interface.


  1. Click the Image Added button and select the Local contacts list.


  1. Click the More soft key, then you can see the Search soft key


  1. Click the Search soft key, you can enter the desired part of name or part of number.


  1. With the search content to match the contact will be automatically displayed on the LCD within 5 seconds.


To search contact in Remote contacts:

  1. Click the Directory soft key on Idle interface.
  2. Click the Image Added button and select the Remote Contacts list.


  1. Select the desired Remote Contact and click Enter soft key.


  1. Click the Search soft key, you can enter the desired part of name or part of number.


  1. With the search content to match the contact will be automatically displayed on the LCD within 5 seconds.


To search contact in LDAP contacts:

  1. Click the Directory soft key on Idle interface.


  1. Click the Image Added button and select the LDAP Contacts list.


  1. Enter the first character or more of contact's name or number.


  1. With the search content to match the contact will be automatically displayed on the LCD within 5 seconds.

Anchor
_Toc509047857
_Toc509047857
Anchor
_Toc509316870
_Toc509316870
Call History Setting

Anchor
_Toc509047858
_Toc509047858
Anchor
_Toc509316871
_Toc509316871
Call History

This phone maintains call history lists of Dialed Calls, Received Calls, Missed Calls and Forwarded Calls. The call history list supports up to100 entries in all on Phone interface and more than 1500 items. You can check the call history, dial a call, add a contact or delete an entry from the call history list. You should enable the history record feature in advance.
To enable the history record feature via Phone interface:

  1. Press Menu?Features?History Setting
  2. Press Image Added and Image Added or Switch soft key to enable History record.
  3. Press Save soft key to save the configuration.

Image Added
To check the call history via Phone interface:

  1. Press the History soft key. The LCD screen displays All Calls list.


  1. Press Right or Left Key to switch among All Calls, Missed Calls, Received Calls, Dialed Calls and Forwarded Calls.


  1. Press to select the desired entry.


  1. Press the Option soft key, and then select Detail from the prompt list.


  1. The detailed information of the entry appears on the LCD screen.

Image Added
To delete an entry from the call history list via Phone interface:

  1. Press the History soft key.


  1. Press Right or Left Key to switch among All Calls, Missed Calls, Received Calls, Dialed Calls and Forwarded Calls.


  1. Press UP or DOWN key to select the desired entry.


  1. Press the Delete soft key.


To delete all entries from the call history list via Phone interface:

  1. Press the History soft key.
  2. Press Right or Left Key to switch among All Calls, Missed Calls, Received Calls, Dialed Calls and Forwarded Calls.
  3. Press the Option soft key, and then select Delete All from the prompt list.
  4. Press the OK soft key.
  5. Press the OK soft key to confirm the deleting or the Cancel soft key to cancel.


To check the call history via Web interface:

  1. Click Directory? Call History
  2. Click Dialed List, Missed List, Received List, Forwarded List then you can see the history list.

Image Added
To Dial a call from Call History via Web interface:

  1. Click Directory?Call History


  1. Select the desired history item, and click Tel Number.


  1. Then the call is dialed on phone.

Image Added

Anchor
OLE_LINK5
OLE_LINK5
To Dial a call from Call History via Phone interface:
1. Press History soft key or press Menu → History → Local History
2. Press Image Added and Image Added to select the targeted one.
3. Press the Dial soft key, Image Added , or Image Added , or the corresponding line key.

Anchor
_Toc509047859
_Toc509047859
Anchor
_Toc509316872
_Toc509316872
Audio Setting

Anchor
_Time_and_Date
_Time_and_Date
Anchor
_Toc347846640
_Toc347846640
Anchor
_Toc350702758
_Toc350702758
Anchor
_Toc509047860
_Toc509047860
Anchor
_Toc509316873
_Toc509316873
Ring Tone

You can adjust the type and volume of the ring tone.
To adjust the Ring Tone Type via Phone interface:

  1. Press Menu → Settings → Basic Setting → Ring Tone.
  2. Press Image Added and Image Added to select the aimed one.
  3. Press Image Added or Save soft key to save the configuration.

Image Added
To adjust the Ring Tone Type via Web Interface

  1. Setting → Preference → Ring Tones


  1. Select the wanted one


  1. Click Image Added to save the configuration.

Image Added
To configure Distinctive Ring Tone via Phone Interface

  1. Press Directory
  2. Select the target contact
  3. Press Detail soft key to edit the contact.
  4. Press Image Added and Image Added to select the wanted Ring Tone for the contact
  5. Press Save soft key to save the contact.

Image Added
To configure Distinctive Ring Tone via Web Interface

  1. Directory → Directory → Contact


  1. Choose the Ring Tone you want to use.


  1. Click Image Added → Image Added to save the configuration.

Image Added
Click Ring tone for more information.

Anchor
_Toc509047861
_Toc509047861
Anchor
_Toc509316874
_Toc509316874
Volume

You can adjust the volume for the phone by the volume keys: Image Added and Image Added .
To adjust the Ring tone volume via Phone interface:

  1. Option 1: To press Image Added and Image Added on the idle page

Image Added

  1. Option 2: To press Image Added and Image Added during the call is ringing.

Image Added
To adjust the handset volume via Phone interface:
To press Image Added and Image Added during a call in handset mode.
Image Added
To adjust the headset volume via Phone interface:
To press Image Added and Image Added during a call in headset mode.
Image Added
To adjust the speaker Volume via Phone interface:
To press Image Added and Image Added during a call in speaker mode.
Image Added

Anchor
_Toc475004873
_Toc475004873
Anchor
OLE_LINK97
OLE_LINK97
Anchor
OLE_LINK98
OLE_LINK98
Anchor
_Toc509047862
_Toc509047862
Anchor
_Toc509316875
_Toc509316875
Voice Mail Tone

This option can set whether to play the beep for phone's voice mail

  1. Click the Setting ? Preference


  1. Select On or Off for Voice Mail Tone.


  1. Click Image Added for the setting.

Image Added

Anchor
_Wallpaper
_Wallpaper
Anchor
_LED_Status_Setting
_LED_Status_Setting
Anchor
_Toc475004874
_Toc475004874
Anchor
_Toc347846647
_Toc347846647
Anchor
_Toc350702765
_Toc350702765
Anchor
_Toc509047863
_Toc509047863
Anchor
_Toc509316876
_Toc509316876
Play Hold Tone

Anchor
OLE_LINK123
OLE_LINK123
Anchor
OLE_LINK124
OLE_LINK124
When you hold the phone, Whether to play hold tone

  1. Click the Setting à Preference


  1. Set On or Off for Play Hold Tone.


  1. Click Image Added for the setting.

Image Added

Anchor
_Toc475004875
_Toc475004875
Anchor
_Toc509047864
_Toc509047864
Anchor
_Toc509316877
_Toc509316877
Play Hold Tone Delay

When you hold the phone. How many seconds to play beep?

  1. Click the Setting à Preference


  1. Set the value for Play Hold Tone Delay.


  1. Click Image Added for the setting.

Image Added

Anchor
_Toc475004876
_Toc475004876
Anchor
_Toc509047865
_Toc509047865
Anchor
_Toc509316878
_Toc509316878
System Settings

Anchor
_Toc509047866
_Toc509047866
Anchor
_Toc509316879
_Toc509316879
Dial Plan

Dial plan is a string of characters that governs the way this phone processes the inputs received from your phone keypad. This phone supports dial plan with following accept digits:
1,2,3,4,5,6,7,8,9,0, *, #

Grammar

Description

x

any digit from 0-9;

xx+

at least 2-digit number;

^

exclude;

,

hear dial tone;

<ac:structured-macro ac:name="unmigrated-wiki-markup" ac:schema-version="1" ac:macro-id="724d8e51-fed1-4b3e-a8e2-7be9e4b86bda"><ac:plain-text-body><![CDATA[

[3-5]

any digit of 3, 4, or 5;

]]></ac:plain-text-body></ac:structured-macro>

<ac:structured-macro ac:name="unmigrated-wiki-markup" ac:schema-version="1" ac:macro-id="11363525-c8b2-454c-9635-6e55fe816684"><ac:plain-text-body><![CDATA[

[147]

any digit 1, 4, or 7;

]]></ac:plain-text-body></ac:structured-macro>

<2=011>

replace digit 2 with 011 when dialing.


To configure dial plan via Web interface:

  1. Click Account →Basic →Dial Plan.


  1. Fill the value in dial plan field.


  1. Click Image Added to save the configuration.

Image Added

Note:
<ac:structured-macro ac:name="unmigrated-wiki-markup" ac:schema-version="1" ac:macro-id="a307b001-c8f2-4ed9-85ba-605d89092a8e"><ac:plain-text-body><![CDATA[Illegal input will fall back to default: {[x]+}. For More, please refer to* [www.htek.com

http://www.htek.com]

]]></ac:plain-text-body></ac:structured-macro>

Anchor
_Toc509047867
_Toc509047867
Anchor
_Toc509316880
_Toc509316880
Dial-Now Timeout

Dial-Now Timeout means that when you enter the number which is matching with dial plan, it will dial out automatically after some time when you stop entering the number.
To configure Dial-Now Timeout via Web interface:

  1. Click Web interface Setting → Preference


  1. Fill the blank of Dial-Now Timeout: for example, 5(seconds). (0 means dial out immediately).


  1. Click the Image Added button to save the configuration

Image Added

Anchor
_Toc509047868
_Toc509047868
Anchor
_Toc509316881
_Toc509316881
No Key Entry Timeout

No Key Entry Timeout means that when you enter the number, it will dial out automatically after some time when you stop enter the number.
To configure No Key Entry Timeout via Web interface:

  1. Click Web interface Setting → Preference


  1. Fill the blank of No Key Entry Timeout: for example, 5(seconds). 0 means never timeout, you should press the send key the dial out the number.


3. Click the Image Added button to save the configuration.
Image Added

Anchor
_Toc509047869
_Toc509047869
Anchor
_Toc509316882
_Toc509316882
Emergency Call

Public telephone networks in countries around the world have a single emergency telephone number (emergency services number), that allows a caller to contact local emergency services for assistance when required. The emergency telephone number may differ from country to country. It is typically a three-digit number that can be easily remembered and dialed quickly. Some countries have a different emergency number for each of the different emergency services.
You can specify the emergency telephone numbers on the IP phone for contacting the emergency services in an emergency situation.
To configure emergency call via Web interface:

  1. Click Setting?Features?Phone Lock


  1. Enter the emergency services number (e.g.110,119,120) in the Emergency field,


  1. Click Image Added to save the configuration.

Image Added

Anchor
_Toc475004881
_Toc475004881
Anchor
OLE_LINK77
OLE_LINK77
Anchor
OLE_LINK94
OLE_LINK94
Anchor
_Toc509047870
_Toc509047870
Anchor
_Toc509316883
_Toc509316883
Label Scroll

When setting function keys, you need to set the label of the function keys. If the words are too long to show on the label, you can use this function to make labels scroll. Another approach is to set the labels to long label mode.
To configure Label Scroll via Web interface:

  1. Click the Setting ? Preference


  1. Select Enable or Disable for Label Scroll.


  1. Click Image Added for the setting.

Image Added

Anchor
OLE_LINK95
OLE_LINK95
Anchor
OLE_LINK96
OLE_LINK96
Anchor
_Toc475004882
_Toc475004882
Anchor
_Toc509047871
_Toc509047871
Anchor
_Toc509316884
_Toc509316884
Show Missed Calls

Whether to show missed call notification on LCD
To configure Show Missed Calls via Web interface:

  1. Click the Setting ? Preference


  1. Select Yes or No for Show Missed Calls.


  1. Click Image Added for the setting.

Image Added

Anchor
_Toc475004883
_Toc475004883
Anchor
OLE_LINK99
OLE_LINK99
Anchor
OLE_LINK100
OLE_LINK100
Anchor
_Auto_Logout_Time
_Auto_Logout_Time
Anchor
_Toc509047872
_Toc509047872
Anchor
_Toc509316885
_Toc509316885
Auto Logout Time

Set the Web login timeout

  1. Click the Setting ? Preference


  1. Set number 1~5000 min for Auto Logout Time.


  1. Click Image Added for the setting.

Image Added

Anchor
_Reboot_in_Talking
_Reboot_in_Talking
Anchor
_Toc475004884
_Toc475004884
Anchor
_Toc509047873
_Toc509047873
Anchor
_Toc509316886
_Toc509316886
Reboot in Talking

This function is to allow reboot during the calls or not

  1. Click the Setting à Preference


  1. Set Enable or Disable for Reboot in Talking.


  1. Click Image Added for the setting.

Image Added

Anchor
_Detect_IP_Conflict
_Detect_IP_Conflict
Anchor
_Toc475004885
_Toc475004885
Anchor
_Toc509047874
_Toc509047874
Anchor
_Toc509316887
_Toc509316887
Detect IP Conflict

LCD can display message when IP conflict

  1. Click the Setting à Preference


  1. Set Enable or Disable for Detect IP Conflict.


  1. Click Image Added for the setting.

Image Added

Anchor
_Redial_Mode
_Redial_Mode
Anchor
OLE_LINK103
OLE_LINK103
Anchor
_Toc475004886
_Toc475004886
Anchor
OLE_LINK104
OLE_LINK104
Anchor
_Toc509047875
_Toc509047875
Anchor
_Toc509316888
_Toc509316888
Redial Mode

Call redial has two ways:(1) To redial the last placed call from the IP Phone (2) To redial the call from all calls list

  1. Click the Setting à Preference


  1. Set Direct Mode or Select Mode for Redial Mode.


  1. Click Image Added for the setting.

Image Added

Anchor
_Suppress_DTMF_Display
_Suppress_DTMF_Display
Anchor
_Toc475004888
_Toc475004888

Anchor
_Toc475004887
_Toc475004887
Anchor
_Toc509047876
_Toc509047876
Anchor
_Toc509316889
_Toc509316889
Keypad Lock

To enable Keypad Lock via Phone interface
1. Press Menu-SettingsAdvanced SettingPhone Setting-Lock
2. Press Image Added and Image Added key or Switch to change selected lock type: All Keys, Menu Key, Function Key, Lock & Answer
3. Press Save or OK key to save the configuration.
To disable Keypad Lock via Phone interface

  1. Press Menu-SettingsAdvanced SettingPhone Setting-Lock


  1. Press Image Added and Image Added key or Switch to change to choose Disable.


  1. Press Save or OK key to save the configuration.


To enable Keypad Lock via Web interface

  1. Click Web interface Setting → Features


  1. To choose the Phone Lock.


  1. To fill the Phone Unlock Pin and Auto Lock Time-Out


  1. Fill the Emergency Number, when the phone is Lock, only Emergency Number can be sent.


  1. To click Image Added to save the configuration.

Image Added
To Disable Keypad Lock via Web interface
1. Click Web interface Setting →Features
2. To choose Disable for the Phone Lock.
3. To click Image Added to save the configuration.

Anchor
_Toc509047877
_Toc509047877
Anchor
_Toc509316890
_Toc509316890
Suppress DTMF Display

In order to ensure safety in Call process, you can choose whether to hide DTMF

  1. Click the Setting ? Preference


  1. Select On or Off for Suppress DTMF Display.


  1. Click Image Added for the setting.

Image Added

Anchor
_Suppress_DTMF_Display_1
_Suppress_DTMF_Display_1
Anchor
_Toc475004889
_Toc475004889
Anchor
_Toc509047878
_Toc509047878
Anchor
_Toc509316891
_Toc509316891
Suppress DTMF Display Delay

In order to ensure safety

Anchor
OLE_LINK122
OLE_LINK122
Anchor
OLE_LINK121
OLE_LINK121
in Call process, you can choose whether to hide DTMF

  1. Click the Setting ? Preference


  1. Select On or Off for Suppress DTMF Display Delay.


  1. Click Image Added for the setting.

Image Added

Anchor
_Check-Syn_With_Authenticate
_Check-Syn_With_Authenticate
Anchor
_Toc475004890
_Toc475004890
Anchor
OLE_LINK101
OLE_LINK101
Anchor
OLE_LINK102
OLE_LINK102
Anchor
_Toc509047879
_Toc509047879
Anchor
_Toc509316892
_Toc509316892
Check-Syn With Authenticate

If this option is enabled, the server needs to be authenticated before the phone agrees to synchronize.

  1. Click the Setting à Preference


  1. Set Enable or Disable for Check-Syn With Authenticate.


  1. Click Image Added for the setting.

Image Added

Anchor
_Toc509047880
_Toc509047880
Anchor
_Toc509316893
_Toc509316893
Other features settings

Anchor
_Toc509047881
_Toc509047881
Anchor
_Toc509316894
_Toc509316894
Action URL

To configure action URL via Web interface:

  1. Click Setting?Action URL


  1. Fill the needed values in the designated blank spaces.


  1. Click Image Added to save the setting.

Click Action URL for more how to use, or check on www.htek.com
Image Added

Anchor
_Toc509047882
_Toc509047882
Anchor
_Toc509316895
_Toc509316895
Softkey Layout

This feature mainly defines which shown on the soft key in some status. For example, what the soft key displays when dialing, or talking.
To configure Soft key via Web interface:

  1. Click Setting?Softkey Layout


  1. Select Enable for Custom Softkey


  1. Select Call States.


  1. Select the feature from the Disable Keys to Enable Keys field by Image Added

Image Added moves the Disable key to Enable field. Image Added moves the Enable key, and it will back to Disable field.

  1. Click Image Added or Image Added to change to position or each feature.


  1. Click Image Added to save the configuration.

Image Added

Note:
When there more than 5 items in the Enable field, the last soft key will display More, and last two item will show in the next page soft key, you can check by press more.

Anchor
_Programmable_Key
_Programmable_Key
Anchor
_Toc509047883
_Toc509047883
Anchor
_Toc509316896
_Toc509316896
Programmable Key

For the default keys as Soft keys, Navigation keys and so on, you can define them as some specific feature, and it works only on the idle page.
To configure Programmable Key via Web interface:

  1. Click Function Keys?Programmable Key
  2. Select the desired Key to set.
  3. Click Image Added to save the setting.
  4. By clicking Image Added , all setting of the keys will be back to default.

Image Added

Anchor
_Toc509047884
_Toc509047884
Anchor
_Toc509316897
_Toc509316897
Exp Key

It only works when there is an expansion module connected with the phone.
For Exp Key configuration, please refer to: UC46 User manual.

Anchor
_Toc509047885
_Toc509047885
Anchor
_Toc509316898
_Toc509316898
Basic Call Features

Anchor
_Toc347846648
_Toc347846648
Anchor
_Toc350702766
_Toc350702766
Anchor
_Toc509047886
_Toc509047886
Anchor
_Toc509316899
_Toc509316899
Place a Call

There are three ways to dialing a call: Handset, Headset and Hands-free speakerphone.
To place a call by Handset

  1. Pick up the handset, or press a line key and dial the necessary number.
  2. Press Image Added or Image Added or press the Send soft key, then the call is sending.


To place a call by Headset:

  1. Press the Image Added ( light is Green),
  2. Enter the desired number.
  3. Press Image Added or Image Added , or press the Send soft key, then the call is sending.


Using headset to place and answer calls for all time

  1. Click Web interface Setting ?Preference


  1. HeadSet Priority ?Enable


  1. Ringer Device For HeadSet ?Use Headset


  1. Click Image Added to save the setting.


  1. Press Image Added

Image Added
Placing a call by hands-free speakerphone

  1. Press the Image Added , or press the Line key, then you can hear the dial tone.
  2. Press the number.
  3. Press Image Added or Image Added or press the Send soft key, then the call is sending.

To place a call by call history or Directory via Phone interface.

  1. Press the History /Directory soft key (On the idle page) or Menu → History /Directory
  2. Press Image Added and Image Added to select the targeted one.
  3. Press the Send soft key, or Image Added , or Image Added , or the corresponding line key, then the call is sending.


Note:

  1. The Image Added key is set to be a send key. For more information, refer to the Key as Send on page
  2. During the call, you can also change among Headset, Handset or Free-speaker mode.

Anchor
_Toc347846649
_Toc347846649
Anchor
_Toc350702767
_Toc350702767

Making two calls with one line and one account

  1. Press a line key and dial phone number, then make a call.


  1. Press Hold soft key and then press New Call soft key.


  1. Dial another phone number,


  1. Press the Send soft key, or Image Added , then make the second call.


Anchor
_Toc509047887
_Toc509047887
Anchor
_Toc509316900
_Toc509316900
End a Call

Here shows to end a call during three modes:
To end a call by Handset
Press the End Call soft key or hang up the handset, or press Image Added
To end a call under Headset Mode
Press the End Call soft key or press Image Added , or press Image Added .
To end a call under hands-free speakerphone Mode
Press the End Call soft key or press Image Added , or press Image Added .

Note:
During the conference, to end the call is same as mentioned above.

Anchor
_Toc347846650
_Toc347846650
Anchor
_Toc350702768
_Toc350702768

Anchor
_Toc509047888
_Toc509047888
Anchor
_Toc509316901
_Toc509316901
Redial a Call

To redial the last placed call from the IP Phone:
Press Image Added directly when LCD is on the idle interface.

Anchor
_Toc347846651
_Toc347846651
Anchor
_Toc350702769
_Toc350702769
Anchor
_Toc509047889
_Toc509047889
Anchor
_Toc509316902
_Toc509316902
Receive a Call

There are three ways to receive a call when the phone is ringing:
To receive a call by handset
Pick up the handset and now the conversation is built.
To receive a call by headset
Press Image Added and now the conversation is built.
To receive a call by hands-free speaker

  1. Option 1: Press Image Added directly.


  1. Option 2: Press Answer soft key.


  1. Option 3: Press the Line key (flashes red).


Moreover, some other action can be done by soft key when the call is coming.

  1. To press the Reject soft key to reject the call. Or press Image Added to reject the current call.


  1. To press Forward to forward to another phone.


  1. To press Silence soft key, and then the call will keep silent, no ring tone display.


Anchor
_Toc509047890
_Toc509047890
Anchor
_Toc509316903
_Toc509316903
Incoming Call Show Mode

There are two incoming call show modes for this phone:

  1. name and number of the contacts
  2. name and number of the incoming call and the account which is connecting


To set incoming call show mode via Web interface:

  1. Click Setting? Preference


  1. Select the desire mode for the incoming call show mode


  1. Click Image Added to save the setting.

Image Added

Anchor
OLE_LINK21
OLE_LINK21
Anchor
OLE_LINK22
OLE_LINK22
Anchor
_Toc509047891
_Toc509047891
Anchor
_Toc509316904
_Toc509316904
Auto Answer

Enable auto answer feature, you will answer all incoming call automatically.
To enable Auto Answer via Web interface

  1. To Click Profile → Advanced


  1. To choose Yes for the Auto Answer.


  1. To click Image Added to save the configuration.

Image Added
To Disable Auto Answer via Web interface

  1. To Click Profile → Advanced


  1. To choose No for the Auto Answer.


  1. To click Image Added to save the configuration.

Anchor
_Toc347846652
_Toc347846652
Anchor
_Toc350702770
_Toc350702770
Anchor
_Toc509047892
_Toc509047892
Anchor
_Toc509316905
_Toc509316905
Call Hold

When using the hold feature, the Hold icon will show on the display.
Image Added
To make a call on hold during three modes:
To hold a call under handset mode:

  1. Press Hold soft key or Image Added to hold the current call.


  1. Press Resume soft key or Image Added to resume the call on hold.


To hold a call under headset mode:

  1. Press Hold soft key or Image Added to hold the current call.


  1. Press Resume soft key or Image Added to resume the call on hold.


To hold a call during the speaker mode:

  1. Press Hold soft key or Image Added to hold the current call.


  1. Press Resume soft key or Image Added to resume the call on hold.


Anchor
_Toc347846653
_Toc347846653
Anchor
_Toc350702771
_Toc350702771
Anchor
_Toc509047893
_Toc509047893
Anchor
_Toc509316906
_Toc509316906
Call Transfer

This phone supports Blind, Attended and Semi-Attended Transfer.

Anchor
_Toc238354287
_Toc238354287

Blind Transfer
When you use this feature, you can :

  1. Press Image Added or Transfer soft key during the conversation, the call is on hold now.


  1. Enter the number that transfers to.


  1. Press Image Added or Transfer soft key, and now the blind transfer completed.

Anchor
_Toc238354288
_Toc238354288

Attended Transfer
When you use this feature, you can

  1. Press Image Added or Transfer soft key during the conversation, the call is on hold now.

Image Added

  1. Enter the number that transfer to, and press the send soft key or Image Added or Image Added .


  1. Start the second conversation, press Image Added or Transfer soft key, then transfer completed.


Anchor
OLE_LINK2
OLE_LINK2
NOTE:
To transfer calls across SIP domains, SIP service providers must support transfer across SIP domains. Blind transfer will usually use the primary account SIP profile.

Anchor
_Toc347846654
_Toc347846654
Anchor
_Toc350702772
_Toc350702772

Semi-Attended Transfer

  1. Press Image Added or Transfer soft key during the conversation, the call is on hold now.


  1. Enter the number transfer to, and press the send soft key or Image Added or Image Added , then you can hear the ring tone.


  1. Press Image Added or Transfer soft key, and now the Semi-attended transfer completed.


BLF Transfer

  1. Set a Programmable Key or Line Key is set as BLF. For how to set BLF, please refer to BLF


  1. Press Image Added or Transfer soft key during the conversation, the call is on hold now.


  1. Press BLF key then realize blind, attended and Semi-Attended Transfer.


Anchor
OLE_LINK25
OLE_LINK25
Hold transfer on hook:

  1. Anchor
    OLE_LINK28
    OLE_LINK28
    Anchor
    OLE_LINK29
    OLE_LINK29
    Setting ? Features ? Transfer Settings: Hold Transfer On Hook: ON.


  1. A place a call to B, B answer, A press the Hold soft key and place a call to C, A cancel the call when C is ringing or answering, then C and B in the same call and the transfer is successful.

Image Added
Hold transfer on Three Way conference:

        1. Setting ? Preference ? Three Way Call Release Type: Transfer.


  1. A place a call to B, B answer, A place a call to C again, C answer, A press the Conference soft key then A, B and C will establish meeting.


  1. A press the End Call soft key or on-hook to exit the meeting in the process of talking.


  1. Then B and C will continue to talk.

Image Added
Transfer to New Call via Web interface

  1. Click Setting → Features


  1. Select Transfer Mode via DSS key → New Call


  1. Select the desired Line Key and select Transfer in the Type.


  1. Enter the phone number in the Value field.

Image Added
Image Added

NOTE: If the person that wanted to be spoken to do not want to answer the call, then the person that answered the coming call could use this function.


Anchor
Transfer_Release_Trigger
Transfer_Release_Trigger
Transfer Release Trigger
This option defines when the phone sends BYE to the server to release the transferred call.

        1. NOTIFY with 200OK

After receiving REFER request sended by the phone, server will send NOTIFY to the phone, and the phone response 200OK, this is the trigger for the phone to release the call.

        1. 2xx response of REFER

The phone will not release the call until it receives a 2xx response from the server to the phone's REFER request.

        1. BYE for the call

The phone will not release the call until receiving BYE from the server.
Image Added

Anchor
_Toc509047894
_Toc509047894
Anchor
_Toc509316907
_Toc509316907
Call Conference

This IP Phone supports up to 5-way conference.
5-way conference

  1. Assuming that call party A and B are in conversation. A wants to bring C, D and E in a conference


  1. A press the Conference soft key, the call is placed on hold.


  1. A enter the number of C and then press send soft key or Image Added .


  1. C answer the call.
  2. A press Image Added or the Conference soft key, then A, B and C are now in a conference. (and now this is 3-way conference)


  1. A press the Conference soft key, the current 3-way conference is placed on hold.
  2. A enter the number of D and then press send soft key or Image Added .


  1. D answer the call.
  2. A press Image Added or the Conference soft key, then A, B, C and D are now in a conference. (and now this is 4-way conference)


  1. A press the Conference soft key, the call is placed on hold.
  2. A enter the number of E and then press send soft key or Image Added .


  1. E answer the call.
  2. A press Image Added or the Conference soft key, then A, B, C, D and E are now the 5-way conference is built.


  1. A end the call, the conference is finished.

Image Added

Note:

  1. If C does not answer the call, A can back to continue the conversation with B;
  2. Once A hangs up the call, the conference is ended, while if B or C drops the call, A&C or A&B conversation continues.
  3. The conference feature is not available on all servers. For more information, contact your system administrator.
  4. To realize the 5-way conference, the line should be all available.

Anchor
_Toc347846655
_Toc347846655
Anchor
_Toc350702773
_Toc350702773
Anchor
_Toc509047895
_Toc509047895
Anchor
_Toc509316908
_Toc509316908
Call Forward

This phone supports static forward (Always Forward, Busy Forward and No Answer Forward) and dynamic forward
To configure static forward
To configure always forward
With this feature, all incoming calls will forward immediately to configured number.

  1. Press Menu → Features → Call Forward →Always Forward.


  1. Press Image Added and Image Added to select the enable choice


  1. Enter the Forward To number.


  1. Press Image Added or Save soft key to save the configuration.

Image Added
To configure busy forward
With this feature, the incoming calls are immediately forwarded if the phone is busy.

  1. Press Menu →Features → Call Forward →Busy Forward.


  1. Press Image Added and Image Added to select the enable choice.


  1. Enter the Forward To number.


  1. Press Image Added or Save soft key to save the configuration.

Image Added
To configure no answer forward
No Answer Forward: Incoming calls are forwarded if not answered after some time.

  1. Press Menu →Features → Call Forward →No Answer Forward.


  1. Press Image Added and Image Added to select the enable choice


  1. Enter the Forward To number and After Ring Times.


  1. Press Image Added or Save soft key to save the configuration.

Image Added
When the Forward feature is enabled, the Icon Image Added will display on Top of the LCD.
Image Added
To configure Forward via Web Interface

  1. Setting → Features → Forward


  1. Click On for the Always/Busy/No Answer Forward


  1. Fill the Target Number


  1. Fill the After Ring Time


  1. Click Image Added to save the configuration

Image Added
To cancel the forward feature via Phone Interface

  1. Option 1: To press the Image Added key to disable the forward feature.


  1. Option 2: Press Menu →Features → Call Forward → Always/Busy/No Answer Forward.
  2. Press Image Added and Image Added to select the disable choice.
  3. Press Image Added or Save soft key to save the configuration.


To cancel the forward feature via Web Interface

  1. Setting → Features → Forward


  1. Click Off for the Always/Busy/No Answer Forward


  1. Click Image Added to save the configuration

To configure dynamic forward
Forward an incoming call during the ringing.

  1. When the phone is ringing, press Forward soft key.


  1. Enter the forward number or select the desired number from Directory soft key (Precondition: local directory has one or more contacts).


  1. Press Image Added or press the Send soft key, then the call is forwarded.

Image Added

Note:
If the Programmable Key or line key is set as BLF, when an incoming call ringing, press this BLF key directly to realize the dynamic forward.
You can choose a desired forward number from the Directory when you press the Forward key.


Anchor
_Call_Return_1
_Call_Return_1
Anchor
_Toc509047896
_Toc509047896
Anchor
_Toc509316909
_Toc509316909
Call Return

This feature allows you to dial the last phone call you received.
To configure the Call Return via Phone interface

  1. Press Menu →Features →Function Keys→ Line Keys as Function Keys → Line Key2(for example)
  2. Press Image Added and Image Added key to select the Call Return in the Type field.
  3. Press Image Added or Save soft key to save the configuration

To configure the Call Return via Web interface

  1. Click Function Keys →Line Key.
  2. Select the desired Line Key and select Call Return in the Type.

Image Added

  1. Click Image Added to save the configuration.

Image Added

Anchor
_Toc475004908
_Toc475004908
Anchor
_Toc509047897
_Toc509047897
Anchor
_Toc509316910
_Toc509316910
Call Back

When this option is set, if the phone you call is busy and does not set call waiting or voice mail, your LCD screen will prompt for call-back, as shown in figure
Image Added
If you press the Callback, the phone will dial the Callback phone number.
To configure the Call Back via Web interface

  1. Click Setting →Features →Callback .


  1. Fill the Callback phone number.


  1. Click Image Added to save the configuration.

Image Added

Anchor
_Toc509047898
_Toc509047898
Anchor
_Toc509316911
_Toc509316911
Call Waiting Tone

  1. Click Setting → Features


  1. Select Call Waiting: On and Call Waiting Tone: On

Image Added
To Change the Call Waiting Tone time via Web interface
1. Click Setting → Tones
Image Added
2. Change the Tone Time as you want (for example 3s)
Image Added

Anchor
_Toc347846645
_Toc347846645
Anchor
_Toc350702763
_Toc350702763
Anchor
_Toc509047899
_Toc509047899
Anchor
_Toc509316912
_Toc509316912
Hide Caller ID

Just enable the unknown/hidden caller feature, by enabling Anonymous call feature thereby the receiver won't be able to know who is calling them.
To configure anonymous call

  1. Press Menu →Features →Anonymous Call →Account ID 1


  1. Press Image Added and Image Added to select the enable choice in Anonymous Call filed.


  1. Enter the Call On Code (optional), Call Off Code (optional).


  1. Press Image Added or Save soft key to save the configuration.

Image Added
To cancel anonymous call feature

  1. Press Menu →Features →Anonymous Call
  2. Press Image Added and Image Added key to select the disable choice in Anonymous Call filed.
  3. Press Image Added or Save soft key to save the configuration.

Anchor
_Toc509047900
_Toc509047900
Anchor
_Toc509316913
_Toc509316913
Reject Anonymous

If you do not want to be disturb by anonymous calls, you can set the reject anonymous call features, so you will not hear the unknown calls
To configure rejecting anonymous call

  1. Press Menu →Features →Anonymous Call →Account ID 1


  1. Press Image Added and Image Added key to select the enable choice in Rejection filed.


  1. Press Image Added or Save soft key to save the configuration

Image Added
To cancel rejecting anonymous call

  1. Press Menu →Features →Anonymous Call →Account ID 1


  1. Press Image Added and Image Added key to select the disable choice in Rejection filed.


  1. Press Image Added or Save soft key to save the configuration.
    Anchor
    _Toc347846662
    _Toc347846662
    Anchor
    _Toc350702780
    _Toc350702780

Anchor
_Toc509047901
_Toc509047901
Anchor
_Toc509316914
_Toc509316914
Call Mute

When you use the Mute feature, the other parties will not hear your voice while you can hear their voice. Call mute applies to all modes (handset, headset, and speakerphone).
Image Added
To mute the call during a call (including a conference call)

  1. Press the Mute key Image Added , then the Mute key glows green, and the LCD display Image Added


  1. To disable the mute function, press Image Added again.

Anchor
_Toc347846663
_Toc347846663
Anchor
_Toc350702781
_Toc350702781
Anchor
_Toc509047902
_Toc509047902
Anchor
_Toc509316915
_Toc509316915
DND

When you use the DND feature, the phone is to reject all incoming calls automatically and you can see the mute icon Image Added shown on the Top of the LCD on idle page.
Image Added
To enable DND feature via Phone interface
Press the DND soft key when the phone is idle, and then Image Added shown on the LCD.
To disable DND feature via Phone interface:
Press the DND soft key again, and then there is no Image Added on the LCD.

Anchor
_Toc509047903
_Toc509047903
Anchor
_Toc509316916
_Toc509316916
Hot Line

To configure Hot Line via Phone interface

  1. Press Menu →Features → Hot Line


  1. Enter the Number and Delay time (as present, we support off hook auto dial).


  1. Press Image Added or Save soft key to save the configuration

Image Added
To configure Hotline auto dial via Web Interface

  1. Setting → Features → HotLine.


  1. Fill the number in the Hotline Number and Hotline Time-out.


  1. Click Image Added to save the configuration.

Image Added
Delete the hotline number and save the configuration, then now the Hotline auto dial is cancelled.

Anchor
_Toc475004915
_Toc475004915
Anchor
_Toc509047904
_Toc509047904
Anchor
_Toc509316917
_Toc509316917
Auto Redial

When this option is set, if the phone you call is busy and does not set call waiting or voice mail, your LCD screen will prompt for Auto Redial, as shown in figure.
Image Added
If you press OK, your LCD will prompt Auto Redial Interval and Auto Redial Times
To configure Auto Redial via Web Interface

  1. Click Setting →Features → Auto Redial


  1. Select On or Off for Auto Redial.


  1. Fill the number 1~300 seconds for the Auto Redial Interval.


  1. Fill the number 1~300 times for the Auto Redial Times.


  1. Click Image Added to save the configuration.

Image Added

Anchor
_Toc347846664
_Toc347846664
Anchor
_Toc350702782
_Toc350702782
Anchor
_Toc509047905
_Toc509047905
Anchor
_Toc509316918
_Toc509316918
Function Key Features and Settings

The function key supports the Line Label Length, Line Page Indicator, BLF list MODE, line key as cancel:
Line Label Length: if this option is set Long label, then the label's length will be longer, it is used if the string is too long.
Line Page Indicator: Enable this option When the phone has been configured for four pages and current page is first page, the forth page has a BLF and BLF's status is changed, then the forth page's button will flash the red indicator.

Anchor
BLFblink
BLFblink
BLF blink:
Anchor
OLE_LINK86
OLE_LINK86
Anchor
OLE_LINK87
OLE_LINK87
 Turn this option on to make the BLF icon blink when the monitored extension is talking.

Anchor
_Line
_Line
Anchor
_Toc388952858
_Toc388952858
Anchor
_Toc509047906
_Toc509047906
Anchor
_Toc509316919
_Toc509316919
Line

It works same as Line keys.
Line support three Mode (Default, lock and float)
Default mode: If there is an incoming call, the phone won't navigate to the set line key account page if the line key page is set as line type and current page is page four.
Lock mode: If there is an incoming call the line key set account will reflect on the same position on every page when the first page set as the line type.
Float mode: If there is an incoming call, the phone will navigate to the set line key account page if the line key page is set as line type and current page is page four.
To configure Line Feature via Web Interface

  1. Click Function Keys → Line Key.


  1. Select the wanted Key and set as Line.


  1. Select the Account.


  1. Click the Image Added button to save the configuration.

Image Added

Anchor
_Speed_Dial
_Speed_Dial
Anchor
_Toc509047907
_Toc509047907
Anchor
_Toc509316920
_Toc509316920
Speed Dial

With this feature, you can dial one number by pressing the configured speed dial key.
To configure Speed Dial feature via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Speed Dial in the Type field.


  1. Enter the targeted Number.


  1. Press Image Added or Save soft key to save the configuration

Then the selected Line Key will work as Speed Dial.
To configure Speed Dial feature via Web Interface

  1. Click Function Keys → Line Key.


  1. Select the wanted Line Key and set as Speed Dial.


  1. Enter the desired phone number in the Value field.


  1. Select the Account ID


  1. Click the Image Added button to save the configuration.

Image Added

Anchor
_BLF_1
_BLF_1
Anchor
_Toc509047908
_Toc509047908
Anchor
_Toc509316921
_Toc509316921
BLF

You can use the BLF (Busy Lamp Field) feature to monitor a specific extension number whether the e

Anchor
OLE_LINK10
OLE_LINK10
xtension is busy or free.

  1. When the extension you are monitoring is idle, the light is steady green.


  1. When the monitored extension is ringing, the light is blinking red, press the BLF key to pick the phone up directly.


  1. When the monitored extension is calling or in a conversation, the light is steady red.


To configure a BLF key via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example).


  1. Select the targeted Line Key.
  2. Press Image Added and Image Added key to select the BLF in the Type field.


  1. Enter the targeted Value Number.


  1. Press Image Added and Image Added key to select the Account ID.


  1. Enter the Pickup Code.
  2. Press Image Added or Save soft key to save the configuration


To configure a BLF key via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Line Key and select BLF in the Type.


  1. Enter the monitored phone number in the Value field.


  1. Select the Account ID


  1. Fill the Extension.


  1. Click Image Added to save the configuration.

Image Added

Note:
This feature is not available on all servers. For more information, contact your system administrator.
After setting the BLF key, do not need to restart the phone.

Anchor
_Toc475004920
_Toc475004920
Anchor
OLE_LINK111
OLE_LINK111
Anchor
OLE_LINK112
OLE_LINK112
Anchor
_Toc509047909
_Toc509047909
Anchor
_Toc509316922
_Toc509316922
Visual Alert for BLF Pickup

Anchor
OLE_LINK127
OLE_LINK127
Anchor
OLE_LINK128
OLE_LINK128
If this option is enabled, when you use the BLF feature to monitor a specific phone whether it is busy or free, you can see this message on the LCD, as shown in the following figure.
Image Added
To configure Visual Alert for BLF Pickup via Web Interface

  1. Click Setting →Features →Call Pickup→ Visual Alert for BLF Pickup


  1. Select Enable or Disable for Visual Alert for BLF Pickup


  1. Click Image Added to save the configuration.

Image Added

Anchor
OLE_LINK125
OLE_LINK125
Anchor
OLE_LINK126
OLE_LINK126
Anchor
_Toc475004921
_Toc475004921
Anchor
_Toc509047910
_Toc509047910
Anchor
_Toc509316923
_Toc509316923
Audio Alert for BLF Pickup

If this option is enabled, when you use the BLF feature to monitor a specific phone whether it is busy or free, you can hear beep.
To configure Audio Alert for BLF Pickup via Web Interface

  1. Click Setting →Features →Call Pickup→ Audio Alert for BLF Pickup


  1. Select Enable or Disable for Audio Alert for BLF Pickup


  1. Click Image Added to save the configuration.

Image Added

Anchor
_Voice_Message
_Voice_Message
Anchor
_BLF_List
_BLF_List
Anchor
_Toc509047911
_Toc509047911
Anchor
_Toc509316924
_Toc509316924
BLF List

To configure BLF List via Web interface:

  1. Login and click Account?Basic


  1. Fill the Eventlist BLF URL and click Image Added to save the configuration.

Image Added

  1. To configure BLF List Keys


3.1 Click?Function Keys?Line Key
3.2 Select the BLF List in the Type field.
3.3. Select Account
3.4 Click Image Added to save the configuration.
For more information, please check on www.htek.com .

Anchor
_Toc509047912
_Toc509047912
Anchor
_Toc509316925
_Toc509316925
Voice Message

This phone supports Voicemail, and when there is a message, the message Image Added will light green. Moreover, when you pick up the handset, or press Speaker key, you will hear some faster busy tone.
Image Added
To configure the Voice mail feature via Phone interface:

  1. Press Menu →Messages →Voice Mail →Set Voice Mail.


  1. Enter the Account No.1/2/3/4/5/6.../16


  1. Press Image Added or Save soft key to save the configuration


To configure Voice Mail Line Key via Web Interface:

  1. Click Function Keys → Line Key.


  1. Select the wanted Key.


  1. Enter the desired voicemail feature codes in the Value field.


  1. Fill the Label name to be displayed on LCD.


  1. Select the Account.


  1. Click Image Added to save the configuration.

Image Added
To configure a Voice mail key by Phone interface:

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example).


  1. Select the
    Anchor
    OLE_LINK44
    OLE_LINK44
    Anchor
    OLE_LINK45
    OLE_LINK45
    targeted Line Key.
  2. Press Image Added and Image Added key to select the Voice Mail in the Type field.


  1. Enter the Value.


  1. Press Image Added and Image Added key to select the Account ID.


  1. Press Image Added or Save soft key to save the configuration


To leave a voice mail:
You can leave a voice mail when the receiver is busy or its inconvenient for them to answer the call. Follow the voice prompt from the system server to leave a voice mail, and then hang up.
To listen to voice mails:
When the Phone interface prompts receiving new voice mail's icon, the power indicator LED flashes red(Setting->Preference: Enable Voice Message Status) and the voice message button flashes green.

  1. Press Image Added or the
    Anchor
    OLE_LINK46
    OLE_LINK46
    Anchor
    OLE_LINK47
    OLE_LINK47
    targeted Line Key to dial out the voice mail access code.


  1. Follow the voice prompt to listen to voice mail.

To view the voicemail via Phone interface:
Press Menu->Messages->Voice Mail->View Voice Mail.
The LCD screen displays the amount of new and old voice mails
Image Added

Note:
This feature is not available on all servers. For more information, contact your system administrator.
Before listening to voice mails, make sure the voice mail access code has been configured.
When all new voice mails are retrieved, the power

Anchor
OLE_LINK48
OLE_LINK48
Anchor
OLE_LINK49
OLE_LINK49
indicator LED, voice mail indicator LED and targeted Line Key will go out.


Anchor
_Direct_Pickup
_Direct_Pickup
Anchor
_Toc509047913
_Toc509047913
Anchor
_Toc509316926
_Toc509316926
Direct Pickup

With this feature, you can pick up the set line when it ringing.
To configure Direct Pickup feature via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the PickUP in the Type field.


  1. Enter the Value.


  1. Press Image Added and Image Added key to select the Account ID.


  1. Press Image Added or Save soft key to save the configuration


Then the selected Line Key will work as Direct Pickup.
To configure Direct Pickup feature via Web Interface

  1. Click Function Keys → Line Key.


  1. Select the wanted Line Key and set as Direct Pickup.


  1. Enter the desired phone number in the Value field.


  1. Select the Account.


  1. Click Image Added to save the configuration.

Image Added

Anchor
_Group_Pickup
_Group_Pickup
Anchor
_Toc509047914
_Toc509047914
Anchor
_Toc509316927
_Toc509316927
Group Pickup

With this feature, you can pick up the specified group that you want incoming calls.
To configure the Pickup via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Group in the Type field.


  1. Enter the group pickup code or the direct pickup code followed the desired phone number in the Value field.
  2. Press Image Added and Image Added key to select the Account ID.
  3. Press Image Added or Save soft key to save the configuration


To configure the Group Pickup via Web interface

  1. Click Function Keys → Line Key.
  2. Select the desired Line Key and select Group Pickup in the Type.
  3. Enter the group pickup code or the direct pickup code followed the desired phone number in the Value field.
  4. Select the Account.
  5. Click Image Added to save the configuration.

Image Added
Image Added

Anchor
_Call_Park
_Call_Park
Anchor
_Toc509047915
_Toc509047915
Anchor
_Toc509316928
_Toc509316928
Call Park

With this feature, you can put a call on hold and continue the conversation from another phone.
To configure the Call Park via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added or press Switch soft key to select the Call Park type.
  2. Select the Account ID.
  3. Enter the call park code in the Value field
  4. Press Image Added or Save soft key to save the configuration


To configure the Call Park via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Line Key and select Call Park in the Type.


  1. Enter the call park code in the Value field.


  1. Select the Account.


  1. Click the Image Added button to save the configuration.

Image Added
For More information for Call Park, please see on www.htek.com

Anchor
_Intercom
_Intercom
Anchor
_Toc347846665
_Toc347846665
Anchor
_Toc350702783
_Toc350702783
Anchor
_Toc509047916
_Toc509047916
Anchor
_Toc509316929
_Toc509316929
Intercom

When use the intercom feature, you can quickly get access connect to the configured one.
To configure intercom feature via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Intercom in the Type field.


  1. Enter the intercom codes followed by desired number in the Value field.


  1. Select the Account ID.
  2. Press Image Added or Save soft key to save the configuration

Then the selected Line Key will work as intercom.
To configure Intercom feature via Web Interface

  1. Click Function Keys → Line Key.


  1. Select the wanted Line Key.


  1. Enter intercom codes followed by desired number in the Value field.


  1. Select the Account.


  1. Click the Image Added button to save the configuration.

Anchor
OLE_LINK8
OLE_LINK8
Image Added
If you want to achieve the intercom feature, you must enable the "Allow Auto Answer by Call-Info"

  1. Click Profile


  1. Select the desired profile from the pull-down list of Profile in the Profile field.


  1. Click Advanced


  1. Enable the "Allow Auto Answer By Call-Info"
  2. Click the Image Added button to save the configuration.

Image Added

Note:
This feature is not available on all servers. For more information, contact your system administrator.

Anchor
_BLF
_BLF
Anchor
_Toc475004928
_Toc475004928
Anchor
_Toc509047917
_Toc509047917
Anchor
_Toc509316930
_Toc509316930
Intercom Barge

If this option is on, when there is an active call and an incoming intercom call arrives, the previous call will be put on hold and the intercom call will be answered

  1. Click the Setting à Preference


  1. Set On or Off for Intercom Barge.


  1. Click Image Added for the setting.

Image Added

Note:
This feature is not available on all servers. For more information, contact your system administrator.


Anchor
_DTMF
_DTMF
Anchor
_Toc509047918
_Toc509047918
Anchor
_Toc509316931
_Toc509316931
DTMF

When the key is configured as DTMF key, you are allowed to send out the desired DTMF number during the conversation.
To use this feature, you should sure that the DTMF Tone is on.
To configure the DTMF via Web Interface

  1. Click Setting?Preference


  1. Select On for Keypad DTMF Tone.


  1. Click Image Added to save the configuration.

Image Added
To configure the DTMF via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the DTMF in the Type field.


  1. Enter the value with the Desired DTMF number


  1. Press Image Added or Save soft key to save the configuration


To configure the DTMF via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Line Key and select DTMF in the Type.


  1. Fill the value with the Desired DTMF number.


  1. Click the Image Added to save the configuration.

Image Added

Anchor
_Prefix
_Prefix
Anchor
_Toc509047919
_Toc509047919
Anchor
_Toc509316932
_Toc509316932
Prefix

If the key is configured as Prefix key, you can set the number prefix (e.g. Before the number plus 9), then you don't input 9, press the key and 9 will display on the LCD interface.
To configure the Prefix via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Prefix in the Type field.


  1. Enter the Value with number that you want to set as prefix


  1. Press Image Added or Save soft key to save the configuration


To configure the Prefix via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Line Key and select Prefix in the Type.


  1. Fill the Value.


  1. Click Image Added to save the configuration.

Then when you press this key, the set value is input directly.
Image Added

Anchor
_Local_Group
_Local_Group
Anchor
_Toc390776801
_Toc390776801
Anchor
_Toc509047920
_Toc509047920
Anchor
_Toc509316933
_Toc509316933
Local Group

When use the Local Group feature, press the key and enter the local Contacts interface quickly.
To configure the Local group via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Local Group in the Type field.


  1. Press Image Added or Save soft key to save the configuration


To configure the Local Group via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Key and select Local Group in the Type.


  1. Click Image Added to save the configuration.

Then you can press the Local Group key to access the pre-defined contact group in the local directory quickly.
Image Added

Anchor
_XML_Group
_XML_Group
Anchor
_Toc390776802
_Toc390776802
Anchor
_Toc509047921
_Toc509047921
Anchor
_Toc509316934
_Toc509316934
XML Group

When use the XML Group feature, press the key and enter the Remote Contacts interface quickly.
To configure the XML group via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the XML Group in the Type field.
  2. Press Image Added and Image Added key to select the Account ID.
  3. Press Image Added or Save soft key to save the configuration


To configure the XML Group via Web interface

  1. Click Function Keys → Line Key.
  2. Select the desired Key and select XML Group in the Type.
  3. Select the Account.
  4. Click Image Added to save the configuration.

Image Added

Anchor
_LDAP
_LDAP
Anchor
_Toc390776803
_Toc390776803
Anchor
_Toc509047922
_Toc509047922
Anchor
_Toc509316935
_Toc509316935
LDAP

When use the LDAP feature, you can get the LDAP Phonebook directly.
To configure the LDAP via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the LDAP in the Type field.


  1. Press Image Added or Save soft key to save the configuration


To configure the LDAP via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Key and select LDAP in the Type.


  1. Click Image Added to save the configuration.

Image Added

Anchor
_XML_Browser
_XML_Browser
Anchor
_Toc390776804
_Toc390776804
Anchor
_Toc509047923
_Toc509047923
Anchor
_Toc509316936
_Toc509316936
XML Browser

You can use this key feature to access the Xml Browser quickly. The XML Browser allows you to create custom services which meet your functional requirements on the server. You can customize practical applications, such as weather report, stock information, Google search, etc.
To configure the XML Browser via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the XML Browser in the Type field.


  1. Fill the access URL for xml browser


  1. Press Image Added or Save soft key to save the configuration


To configure the XML Browser via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Key and select xml browser in the Type.


  1. Fill the access URL for xml browser (e.g.: http://192.168.0.106/XMLBrowser/TextMenu.xml)


  1. Click Image Added button to save the configuration.

Image Added

Anchor
_Broadsoft_Group
_Broadsoft_Group
Anchor
_Toc390776805
_Toc390776805
Anchor
_Toc509047924
_Toc509047924
Anchor
_Toc509316937
_Toc509316937
Broadsoft Group

When using the BroadSoft Group feature, by just pressing the key you can enter the Broadsoft Contacts interface quickly.
To configure the Broadsoft Group via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Broadsoft Group in the Type field.


  1. Press Image Added or Save soft key to save the configuration


To configure the Broadsoft Group via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Key and select Broadsoft Group in the Type.


  1. Click the Image Added button to save the configuration.

Anchor
_Conference
_Conference
Anchor
_Toc390776806
_Toc390776806
Anchor
_Toc509047925
_Toc509047925
Anchor
_Toc509316938
_Toc509316938
Conference

The Htek IP Phone supports up to 5-way conference. You are allowed to configure the line key to be used as a conference key. This key works same as Image Added .
To configure the Conference via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Conference in the Type field.


  1. Press Image Added or Save soft key to save the configuration


To configure Conference via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Conference in the Type.


  1. Click the Image Added button to save the configuration.


Anchor
_Forward
_Forward
Anchor
_Toc390776807
_Toc390776807
Anchor
_Toc509047926
_Toc509047926
Anchor
_Toc509316939
_Toc509316939
Forward

If the key is configured as Forward key, press this key under the idle status, the IP phone will turn to the Always Forward interface and you can set the Forward to number, then when there is any call to that number it will be forwarded to the set number automatically.
To configure the Forward via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Forward in the Type field.


  1. Enter the Number to forward to.


  1. Press Image Added or Save soft key to save the configuration


To configure Forward via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Forward in the Type.


  1. Enter the Value with the number you want to forward to.


  1. Click the Image Added
    Anchor
    OLE_LINK13
    OLE_LINK13
    Anchor
    OLE_LINK14
    OLE_LINK14
    button to save the configuration.

Anchor
_Forward_1
_Forward_1
Anchor
_Transfer
_Transfer
Anchor
_Toc390776808
_Toc390776808
Anchor
_Toc509047927
_Toc509047927
Anchor
_Toc509316940
_Toc509316940
Transfer

You are able to configure the key as a transfer key to perform the Blind/Attended/ Semi-Attended Transfer.
To configure the Transfer via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Transfer in the Type field.


  1. Enter the Number to transfer to


  1. Press Image Added or Save soft key to save the configuration


To configure Transfer via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Transfer in the Type.


  1. Enter the Value with the number that wanted transfer to


  1. Click the Image Added button to save the configuration.

Anchor
_Hold
_Hold
Anchor
_Toc390776809
_Toc390776809
Anchor
_Toc509047928
_Toc509047928
Anchor
_Toc509316941
_Toc509316941
Hold

The key can be configured as a hold key. You can use this key to hold and resume a call during the conversation.
To configure the Hold via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Hold in the Type field.


  1. Press Image Added or Save soft key to save the configuration


To configure Hold via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Hold in the Type.


  1. Click the Image Added button to save the configuration.

Anchor
_Group_Listening
_Group_Listening
Anchor
_Toc390776810
_Toc390776810
Anchor
_Toc509047929
_Toc509047929
Anchor
_Toc509316942
_Toc509316942
Group Listening

With this feature, when you have an active call, you can listen using Handset and Free-speaker, but only can use the handset to speak.
To configure the Group listening via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Group Listening in the Type field.


  1. Press Image Added or Save soft key to save the configuration


To configure Group listening via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Group Listening in the Type.


  1. Click Image Added to save the configuration.

Anchor
_DND
_DND
Anchor
_Toc390776811
_Toc390776811
Anchor
_Toc509047930
_Toc509047930
Anchor
_Toc509316943
_Toc509316943
DND

If the key is configured as DND key, allows you to activate the DND function immediately when you press it and the phone will reject all incoming calls automatically. Press it again to deactivate DND mode.

To configure the DND via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the DND in the Type field.


  1. Press Image Added or Save soft key to save the configuration

To configure DND via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select DND in the Type.


  1. Click the Image Added button to save the configuration.


To enable DND feature
Press the DND soft key when the phone is idle status, and then DND icon is shown on the LCD.
To disable DND feature
Press the DND soft key again, and then there is no DND icon on the LCD.

Anchor
_Redial
_Redial
Anchor
_Toc390776812
_Toc390776812
Anchor
_Toc509047931
_Toc509047931
Anchor
_Toc509316944
_Toc509316944
Redial

If the key is configured as Redial key, you can redial the last placed call from the IP Phone.
To configure Redial via Web Interface

  1. Click Function Keys →Line key


  1. Select the desired Key and select Redial in the Type.


  1. Enter the Label displayed on LCD.


  1. Click the Image Added button to save the configuration.

Anchor
_Call_Return
_Call_Return
Anchor
_SMS
_SMS
Anchor
_Toc390776814
_Toc390776814
Anchor
_Toc509047932
_Toc509047932
Anchor
_Toc509316945
_Toc509316945
SMS

Anchor
_Toc509047933
_Toc509047933
Anchor
_Toc509316946
_Toc509316946
Send SMS

To send SMS via web Interface

  1. Click Setting?SMS


  1. Select the Account (from which account the SMS sent)


  1. Enter the targeted number


  1. Input the content of SMS, and click Send.

Image Added
To send SMS via Phone interface:

  1. Click Menu?Messages?Text Message?Set SMS


  1. Enter the contents in the blank field.


  1. Press the Send button


  1. Select the account in the From field (from which account the SMS sent)


  1. Enter the target number in the To field (to which account the number sent)


  1. Press the Send button.

Anchor
_Toc509047934
_Toc509047934
Anchor
_Toc509316947
_Toc509316947
Set SMS Line Key

To configure the SMS via Phone Interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the SMS in the Type field.


  1. Press Image Added or Save soft key to save the configuration


To configure SMS via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select SMS in the Type.


  1. Click Image Added to save the configuration.
    Anchor
    _Record
    _Record
    Anchor
    _Paging
    _Paging

Anchor
_Record_1
_Record_1
Anchor
_Toc350702788
_Toc350702788
Anchor
_Toc509047935
_Toc509047935
Anchor
_Toc509316948
_Toc509316948
Record

With record feature, you can record your calls by pressing the record key .
To configure the record via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)
  2. Press Image Added and Image Added key to select the Record in the Type field.
  3. Press Image Added or Save soft key to save the configuration

Image Added
To configure the record via Web Interface

  1. Click Function Keys → Line Key.


  1. Select the desired Line Key and select Record in the Type.


  1. Click the Image Added button to save the configuration.

Image Added

Note:
Please contact the system administrator whether support this feature or not.

Anchor
_Toc350702789
_Toc350702789

Anchor
_URL_Record
_URL_Record
Anchor
_Toc509047936
_Toc509047936
Anchor
_Toc509316949
_Toc509316949
URL Record

The phone sends HTTP URL request to trigger a recording. Contact your system administrator for the predefined URL.
To configure the URL record via Phone interface

  1. Press Menu →Features →Function Keys→ Line Keys as Function Keys → Line Key2(for example)
  2. Press Image Added and Image Added key to select the URL Record in the Type field.
  3. Fill the Value.
  4. Press Image Added or Save soft key to save the configuration


To configure the record via Web Interface

  1. Click Function Keys → Line Key.


  1. Select the desired Line Key and select URL Record in the Type.


  1. Fill the Value.
  2. Click the Image Added button to save the configuration.

Anchor
_Paging_1
_Paging_1
Anchor
_Toc509047937
_Toc509047937
Anchor
_Toc509316950
_Toc509316950
Paging

With this feature, you can call a paging group directly.
To configure the paging via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Paging in the Type field.


  1. Enter the paging code followed the number.


  1. Press Image Added and Image Added key to select the Account ID.
  2. Press Image Added or Save soft key to save the configuration


To configure the Paging via Web interface

  1. Click Function Keys → Line Key.


  1. Select the desired Line Key and select Paging in the Type.


  1. Enter the paging code followed the number.


  1. Select the Account.


  1. Click the Image Added button to save the configuration.

Anchor
_Shared_Line
_Shared_Line
Anchor
_Toc350702787
_Toc350702787
Anchor
_Toc509047938
_Toc509047938
Anchor
_Toc509316951
_Toc509316951
Shared Line

Anchor
OLE_LINK70
OLE_LINK70
Anchor
OLE_LINK71
OLE_LINK71
Anchor
OLE_LINK66
OLE_LINK66
Anchor
OLE_LINK67
OLE_LINK67
Htek IP Phone supports "Share Call Appearance" by Broadsoft and XCast standard. This feature allows members of the SCA group to share SIP lines and provides status monitoring (idle, active, progressing, hold) of the share line. When there is an incoming call designated for the SCA group, all of the members of the group will be notified of an incoming call and will be able to answer the call from the phone with the SCA extension registered in the group.
All the users that belong to the same SCA group will be notified by visual indicator when a user seizes the line and places an outgoing call, and all the users of this group will not be able to seize the line until the line goes back to an idle state or when the call is placed on hold (with the exception of when multiple call appearances are enabled on the server side).
In the middle of the conversation, there are two types of hold: Public Hold and Private Hold. When a member of the group places the call on public hold, the other users of the SCA group will be notified of this by the red-flashing button and they will be able to resume the call from their phone by pressing the line button. However, if this call is placed on private-hold, no other member of the SCA group will be able to resume that call.
To enable share call appearance, the user would need to register the share line account on the phone. In addition, they would need to navigate to "Account" > "Advanced" on the webpage and set the line to
Anchor
OLE_LINK64
OLE_LINK64
Anchor
OLE_LINK65
OLE_LINK65
"Share Line" and "SIP Server Type", and configure the line key or Line Key as "line" type with the desired account on webpage or LCD. If the user requires more share call appearances, the user can configure multiple line keys (Function Keys>Line key) to be "line" type associated with the account.
This feature is very useful in the boss and secretary scenario. For example, the secretary can share the boss' extension number on her phone. When there is an incoming call to the extension number of the boss, both the phones of the boss and the secretary will ring simultaneously. Either the boss or the secretary can answer the call. Calls on share line can be placed on hold or barged in.
To configure the line key as line via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)


  1. Press Image Added and Image Added key to select the Line in the Type field.


  1. Press Image Added and Image Added key to select the Account ID.


  1. Enter the Label


  1. Enter the Value


  1. Press Image Added or Save soft key to save the configuration


To configure the line key as line via Web Interface

  1. Click Function Keys → Line Key.


  1. Select the desired Line Key and select Line in the Type.


  1. Enter the Value.


  1. Enter the Label.


  1. Select the Account


  1. Click the Image Added button to save the configuration and then restart.


Note:
This feature is not available on all servers. For more information, contact your system administrator.


Anchor
_Public_Hold
_Public_Hold
Anchor
_Toc388887860
_Toc388887860
Anchor
_Toc388952885
_Toc388952885
Anchor
_Toc509047939
_Toc509047939
Anchor
_Toc509316952
_Toc509316952
Public Hold

The key can be configured as a public hold key. During a conversation, all members belonging to that particular SLA group can use this key to hold or resume a call.
To configure the Public hold via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)
  2. Press Image Added and Image Added key to select the Public Hold in the Type field.
  3. Press Image Added or Save soft key to save the configuration


To configure public hold via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Public Hold in the Type.
  2. Click the Image Added button to save the configuration.

Image Added

Anchor
_Private_Hold
_Private_Hold
Anchor
_Toc388887861
_Toc388887861
Anchor
_Toc388952886
_Toc388952886
Anchor
_Toc509047940
_Toc509047940
Anchor
_Toc509316953
_Toc509316953
Private Hold

The key can be configured as a private hold key. During a conversation, all members belonging to that particular SLA group can use this key to hold the call, but only the initiator can resume the call.
To configure the Private hold via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)
  2. Press Image Added and Image Added key to select the Private Hold in the Type field.
  3. Press Image Added or Save soft key to save the configuration


To configure private hold via Web Interface

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Private Hold in the Type.


  1. Click the Image Added button to save the configuration.

Image Added

Anchor
_URL
_URL
Anchor
_Toc509047941
_Toc509047941
Anchor
_Toc509316954
_Toc509316954
Hot Desking

Hot Desking originates from the definition of being the temporary physical occupant of a work station or surface by a particular employee. A primary motivation for Hot Desking is cost reduction. This feature is regularly used in places where all employees are not in the office at the same time, or not in the office for a very long time, which means their personal offices are often vacant, consuming valuable space and resources.
You can use Hot Desking on the IP phone to logout the existing accounts and then log in a new account, which allows many users to share the phone resource in different times. To use this feature, first you need to configure a Hot Desking key in the advance settings.
This feature is supported on the version 1.0.3.82 or later

Anchor
OLE_LINK15
OLE_LINK15
Anchor
OLE_LINK16
OLE_LINK16
To configure the hot desking via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)
  2. Press Image Added and Image Added key to select the Hot Desking in the Type field.


  1. Enter the display name in the Label field.


  1. Press Image Added or Save soft key to save the configuration


To configure the hot desking via Web interface:

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Hot Desking in the Type.


  1. Select the desired account from the pull-down list of Account field.


  1. Click the Image Added button to save the configuration.

To use the hot desking feature on the user interface:

  1. Press the Hot Desking key when the IP Phone is idle.


  1. Enter the Extension number and password


  1. Click Save soft key

You can see the account information which has changed.

Note:
This feature is not available on all servers. For more information, contact your system administrator.

Anchor
_Toc509047942
_Toc509047942
Anchor
_Toc509316955
_Toc509316955
ACD

ACD feature is often used in offices for customer service, such as call center. The ACD system handles large volumes of incoming calls from callers who have no need to talk to a specific person but who require assistance from any of the different personnel at the earliest point. The ACD feature on the Htek IP Phone allows the ACD system to distribute calls from large volumes of incoming calls to the registered IP phone users. To use this feature, first you should configure an ACD key in the advance settings.
To configure the ACD via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)
  2. Press Image Added and Image Added key to select the ACD in the Type field.


  1. Enter the label in the Label field.


  1. Select the desired account in the Account ID field.
  2. Press Image Added or Save soft key to save the configuration


To configure the ACD via Web interface:

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select ACD in the Type.


  1. Enter the label in the Label field.


  1. Select the desired account from the pull-down list of Account field.


  1. Click the Image Added button to save the configuration.


Note:
This feature is not available on all servers. For more information, contact your system administrator.


Anchor
_Toc509047943
_Toc509047943
Anchor
_Toc509316956
_Toc509316956
Zero Touch

You can use this key feature to configure auto provision and network parameters quickly.

Anchor
OLE_LINK17
OLE_LINK17
Anchor
OLE_LINK18
OLE_LINK18
This feature is supported on the version 1.0.3.82 or later
To configure the zero touch via Phone interface

  1. Press Menu →Features →Function Keys →Line Keys as Function Keys → Line Key2(for example)
  2. Press Image Added and Image Added key to select the
    Anchor
    OLE_LINK11
    OLE_LINK11
    Anchor
    OLE_LINK12
    OLE_LINK12
    Zero Touch in the Type field
  3. Press Image Added or Save soft key to save the configuration


To configure the zero touch via Web interface:

  1. Click Function Keys →Line Key.


  1. Select the desired Key and select Zero Touch in the Type.
  2. Click the Image Added button to save the configuration.


To use the zero touch feature on the user interface:

  1. Press the Zero Touch key when the IP Phone is idle.


  1. Press the OK soft key and the IP Phone will enter the WAN Port interface; you can change the WAN Type by pressing the Navigation keys.


  1. Press the Next soft key to enter Network interface, then you can configure some information.


  1. Press the Next soft key again, you can configure auto provision information.


  1. When you finish the setting, you can press the OK to accept the changes.


Note:
This feature is not available on all servers. For more information, contact your system administrator.


Anchor
_Toc350702790
_Toc350702790
Anchor
_Multicast_Paging
_Multicast_Paging
Anchor
_Toc509047944
_Toc509047944
Anchor
_Toc509316957
_Toc509316957
Multicast Paging

You can use multicast paging to quickly and easily forward out time sensitive announcements to people within the multicast group. You can configure a multicast paging key or a paging list key on the phone, which allows you to send a Real Time Transport Protocol (RTP) stream to the pre-configured multicast address/addresses without involving SIP signaling. You can configure the phone to receive an RTP stream from pre-configured multicast listening address/addresses without involving SIP signaling. You can specify up to 10 multicast listening addresses.

Anchor
_Toc509047945
_Toc509047945
Anchor
_Toc509316958
_Toc509316958
Sending RTP Stream

To configure a multicast paging key via Phone interface

  1. Press Menu →Features →Line Key →Line Key2?e.g.?


  1. Press Image Added and Image Added or switch key to select the Multicast Paging in the Type field.
  2. Enter the multicast IP address and port number (e.g., 224.5.6.20:2000) in the Value field.

The valid multicast IP addresses range from 224.0.0.0 to 239.255.255.255.

  1. Press Image Added or Save soft key to save the configuration


Anchor
OLE_LINK30
OLE_LINK30
Anchor
OLE_LINK31
OLE_LINK31
To configure a multicast paging key via Web interface

  1. Function Keys->Line Key
  2. Select the desired Key and select Multicast Paging in the Type.
  3. Enter the multicast IP address and port number (e.g., 224.5.6.20:2000) in the Value field.

The valid multicast IP addresses range from 224.0.0.0 to 239.255.255.255.

  1. Click the Image Added button to save the configuration.


Sending RTP Stream:
Press the Multicast Paging key when the phone is idle.
The phone sends RTP to a preconfigured multicast address (IP:Port). Any phone in the local network then listens to the RTP on the preconfigured multicast address (IP:Port). For both sending and receiving of the multicast RTP, there is no SIP signaling involved.
The multicast paging key LED illuminates solid green.

Anchor
_Toc509047946
_Toc509047946
Anchor
_Toc509316959
_Toc509316959
Receiving RTP Stream

You can configure the phone to receive a Real Time Transport Protocol (RTP) stream from the pre-configured multicast address/addresses without involving SIP signaling. You can specify up to 10 multicast addresses that the phone listens to on the network.
How the phone handles incoming multicast paging calls depends on Paging Barge and Paging Priority Active parameters configured via web user interface.
Paging Barge
The paging barge parameter defines the priority of the voice call in progress. If the priority of an incoming multicast paging call is lower than that of the active call, it will be ignored automatically. If Disabled is selected from the pull-down list of Paging Barge, the voice call in progress will take precedence over all incoming multicast paging calls.
Valid values in the Paging Barge field: ? 1 to 10: Define the priority of the active call, 1 with the highest priority, 10 with the lowest. ? Disabled: The voice call in progress will take precedence over all incoming paging calls.
Paging Priority Active
The paging priority active parameter decides how the phone handles incoming multicast paging calls when there is already a multicast paging call on the phone. If enabled, the phone will ignore incoming multicast paging calls with lower priorities, otherwise, the phone will answer incoming multicast paging calls automatically and place the previous multicast paging call on hold. If disabled, the phone will automatically ignore all incoming multicast paging calls.
Multicast Codec:
You can only configure the codec by Web interface.
To configure multicast codec key via Web interface

  1. Click Directory ->Multicast Paging:
  2. Select the desired codec from the pull-down list of Multicast Codec
  3. Click
    Anchor
    OLE_LINK34
    OLE_LINK34
    Anchor
    OLE_LINK35
    OLE_LINK35
    the Image Added button to save the configuration.


To configure multicast listening addresses via Web interface:

              1. Click Directory->Multicast Paging?
              2. Select the desired value from the pull-down list of Paging Barge.
              3. Select the desired value from the pull-down list of Paging Priority Active.
              4. Enter the multicast IP address/addresses and port number (e.g., 224.5.6.20:2000) which the phone listens to for incoming RTP multicast in the Listening Address field.
              5. Enter the label in the Label field.
              6. Click Image Added button to save the configuration.

Image Added

Note:
The priorities of listening to multicasting addresses can be predefined: 1 being the highest priority, 10 with the lowest in priority order. Both the multicast paging sender and receiver's phones play a warning tone when establishing a multicast paging call. Listening to Multicasting addresses can be configurable via Web interface only.

Anchor
_Toc509047947
_Toc509047947
Anchor
_Toc509316960
_Toc509316960
Upgrade

Anchor
_Toc509047948
_Toc509047948
Anchor
_Toc509316961
_Toc509316961
Factory Reset

To set Factory Reset by Phone interface

  1. Press Menu → Settings → Advanced Setting (default password: admin) → Phone Setting → Factory Reset
  2. Press OK soft key in the warning page.


To set Factory Reset via Web interface

  1. Click Management → Upgrade
  2. Click Image Added and then confirm the setting.

Image Added

Anchor
_Toc509047949
_Toc509047949
Anchor
_Toc509316962
_Toc509316962
Pcap Feature

To use pcap via Web interface:

  1. Click Management?Tools


  1. Click Start and then operation the phone


  1. When finish the operation, click Stop and then click Export.


  1. Then you'll get the Pcap captures.

Image Added

Anchor
_Toc509047950
_Toc509047950
Anchor
_Toc509316963
_Toc509316963
System Log

To download system log via Web interface:

  1. Click Management?Configuration


  1. Click Image Added of the system Log

Image Added

  1. Then you'll get a txt file: syslog.tgz.

Image Added

Anchor
_Toc509047951
_Toc509047951
Anchor
_Toc509316964
_Toc509316964
Upgrade

To upgrade via HTTP, the "Management"> "auto provision" -> "Firmware Upgrade"> "Upgrade Mode" field needs to be set to HTTP, respectively. "Firmware Server Path" needs to be set to a valid URL of a HTTP server, server name can be in either FQDN or IP address format. Here are examples of some valid URL.
e.g. firmware.mycompany.com:5688/Htek
e.g. www.mycompany.com:5688/fm/ Htek
e.g. 218.2.83.110
Instructions for firmware upgrade via HTTP:
(1) End users can choose to download the free HTTP server from http://httpd.apache.org/ or use
Microsoft IIS web server. Then setup HTTP server.
(2) Unzip the firmware file and put all of them under the root/fm directory of the HTTP server.
(3) Visiting "http://192.168.0.254/

Anchor
OLE_LINK26
OLE_LINK26
Anchor
OLE_LINK27
OLE_LINK27
fm/fw924.rom on localhost by browser" to verify the HTTP Server. If visiting "http://192.168.0.254/fm/fw924.rom on another computer and it not prompted to download fw924.rom file on this computer, please check if the firewall is on or off (Suggest you turn off the firewall).
To configure the server path via Web interface:

  1. Click Management?Auto provision:


  1. Select the upgrade mode in the Upgrade Mode field


  1. Enter the Firmware Server Path and Config Server Path (192.168.0.254 is HTTP server).


  1. Enter the HTTP server's username and password (optional).


  1. Click the Image Added button to save the configuration.


  1. Restart the UC924, IP Phone will restart and auto-get firmware files from HTTP server.

Image Added
NOTES:

  • Htek recommends end-user use the Htek HTTP server. For large companies, we recommend to maintain their own TFTP/HTTP/FTP/HTTPS server for upgrade and provisioning procedures.
  • Once a "Firmware Server Path" is set, user needs to update the settings and restart the IP Phone. If the configured firmware server is found and a new code image is available, the UC924 will attempt to retrieve the new image files by downloading them into the UC924's SDRAM. During this stage, the UC924's LEDs will blink fastly until the checking/downloading process is completed. Upon verification of checksum, the new code image will then be saved into the Flash. If TFTP/HTTP/FTP/HTTPS fails for any reason (e.g. TFTP/HTTP/FTP/HTTPS server is not responding, there are no code image files available for upgrade, or checksum test fails, etc), the UC924 will stop the TFTP/HTTP/FTP/HTTPS process and simply boot using the existing code image in the flash.
  • Firmware upgrade may take as long as 3 to 8 minutes over Internet, or just 1 minutes if it is performed on a LAN. It is recommended to conduct firmware upgrade in a controlled LAN environment if possible. For users who do not have a local firmware upgrade server.
  • Htek's latest firmware is available at www.htek.com ?Support? Document & Firmware.
  • Oversea users are strongly recommended to download the binary files and upgrade firmware locally in a controlled LAN environment.


To upgrade manually via the Web configuration interface

  1. Click Management → Upgrade


  1. Click Image Added or the blank.
  2. Select the firmware (fw924.rom) and then click Image Added .

Image Added

Anchor
_Toc391561062
_Toc391561062
Anchor
_Toc398545782
_Toc398545782
Anchor
_Toc509047952
_Toc509047952
Anchor
_Toc509316965
_Toc509316965
Configuration File

*To download configuration file:*

  1. Click Management ? Configuration ? Configure File
  2. Click the Image Added or Image Added , then you can get a file: cfg.bin or cfg.xml

Image Added
*To Restore a configuration file:*

  1. Click Management ? Configuration ? Configure File


  1. Select the xxx.bin or xxx.xml file, and then Click the Image Added or Image Added , then IP Phone will reboot.

Image Added

Anchor
_Toc350702791
_Toc350702791
Anchor
_Toc509047953
_Toc509047953
Anchor
_Toc509316966
_Toc509316966
Troubleshooting

Anchor
_Toc350702792
_Toc350702792
Anchor
_Toc509047954
_Toc509047954
Anchor
_Toc509316967
_Toc509316967
Why is the phone LCD screen blank?

  • Ensure your phone is properly plugged into a functional AC outlet.
  • Ensure that the phone isn't plugged into a plug controlled by a switch that is off.
  • If the phone is plugged into a power strip, try plugging it directly into a wall outlet instead.
  • If your phone is powered from PoE, ensure you use a PoE compliant switch or hub, or contact your system administrator for more information.
  • Check if the power LED is on to ensure that the phone is powered on.

Anchor
_Toc350702793
_Toc350702793
Anchor
_Toc509047955
_Toc509047955
Anchor
_Toc509316968
_Toc509316968
Why does the phone display "Network Unavailable"?

To resolve:

  • Ensure that the Ethernet cable is plugged into the Internet port on the phone and the Ethernet cable is not loose.
  • Ensure that the switch or hub in your network is functioning well.
  • If the problem still persists, Contact your system administrator for more information.

Anchor
_Toc476237016
_Toc476237016
Anchor
_Toc350702795
_Toc350702795
Anchor
_Toc391561066
_Toc391561066
Anchor
_Toc509047956
_Toc509047956
Anchor
_Toc509316969
_Toc509316969
Why can't I get a dial tone?

To resolve:

  • Check for any loose connections and that the phone has been installed properly. For the Installation instructions, refer to the phone installation section.
  • Check whether dial tone is present on one of the audio modes.
  • Switch between the Handset, Headset (if you have) or Hands-Free Speakerphone to check whether dial tone is present for one of the audio modes.
  • If the dial tone exists on another audio mode, connect a different handset or headset to isolate the problem.

Anchor
_Toc509047957
_Toc509047957
Anchor
_Toc509316970
_Toc509316970
Where to set the tone?

You can set the tone on Web interface:

  • Click Setting?Tones
  • Define the dial tone, ringing, busy tone…
  • For the tones, you can check with your system administrator.
  • For More Click Tone Notes.

Image Added

Anchor
_Toc509047958
_Toc509047958
Anchor
_Toc509316971
_Toc509316971
How to download XML Configuration?

  • Click Management?Configuration? Image Added

Anchor
_Toc391561069
_Toc391561069
Anchor
_Toc398545918
_Toc398545918
Anchor
_Toc509047959
_Toc509047959
Anchor
_Toc509316972
_Toc509316972
How to Import Trusted CA certificate?

  • Click Management?Trusted CA

Image Added

Anchor
_Toc509047960
_Toc509047960
Anchor
_Toc509316973
_Toc509316973
How to Import Server CA certificate?

  • Click Management?Server CA

Image Added

Anchor
_Toc391561070
_Toc391561070
Anchor
_Toc476141464
_Toc476141464
Anchor
_Toc476143818
_Toc476143818
Anchor
_Toc476148468
_Toc476148468
Anchor
_Toc509047961
_Toc509047961
Anchor
_Toc509316974
_Toc509316974
How to use Vlan?

Anchor
_Toc391561071
_Toc391561071
Anchor
_Toc476141465
_Toc476141465
Anchor
_Toc476143819
_Toc476143819
Anchor
_Toc476148469
_Toc476148469
Anchor
_Toc509047962
_Toc509047962
Anchor
_Toc509316975
_Toc509316975
How to use LLDP?

  • For LLDP information, please click VLAN Note
  • VLAN Notes including: 

1. Voice VLAN 
2. Major Benefits of Using VLANs 
3. VLAN discovery method on Htek ip phones 
4. LLDP Feature on Htek IP Phones 
5. Supported TLVS of IP Phones 
6. Configuring LLDP Feature 
7. DHCP VLAN 
8. Open the DHCP VLAN on the Htek IP Phones 
9. VLAN under Bridge Mode 
10. VLAN underNAT Mode

Anchor
_Toc391561072
_Toc391561072
Anchor
_Toc476141466
_Toc476141466
Anchor
_Toc476143820
_Toc476143820
Anchor
_Toc476148470
_Toc476148470
Anchor
_Toc509047963
_Toc509047963
Anchor
_Toc509316976
_Toc509316976
How to Set LCD and Web GUI?

Anchor
_Toc391561073
_Toc391561073
Anchor
_Toc476141467
_Toc476141467
Anchor
_Toc476143821
_Toc476143821
Anchor
_Toc476148471
_Toc476148471
Anchor
_Toc509047964
_Toc509047964
Anchor
_Toc509316977
_Toc509316977
How to Upgrade via FTP?

Anchor
_Toc391561074
_Toc391561074
Anchor
_Toc476141468
_Toc476141468
Anchor
_Toc476143822
_Toc476143822
Anchor
_Toc476148472
_Toc476148472
Anchor
_Toc509047965
_Toc509047965
Anchor
_Toc509316978
_Toc509316978
How to make Ringtone?

Anchor
_Toc391561075
_Toc391561075
Anchor
_Toc476141469
_Toc476141469
Anchor
_Toc476143823
_Toc476143823
Anchor
_Toc476148473
_Toc476148473
Anchor
_Toc509047966
_Toc509047966
Anchor
_Toc509316979
_Toc509316979
How to use Open VPN?

Anchor
_Toc391561076
_Toc391561076
Anchor
_Toc476141470
_Toc476141470
Anchor
_Toc476143824
_Toc476143824
Anchor
_Toc476148474
_Toc476148474
Anchor
_Toc509047967
_Toc509047967
Anchor
_Toc509316980
_Toc509316980
Provisioning Guide on Free PBX

Anchor
_Toc476141471
_Toc476141471
Anchor
_Toc476143825
_Toc476143825
Anchor
_Toc476148475
_Toc476148475
Anchor
_Toc509047968
_Toc509047968
Anchor
_Toc509316981
_Toc509316981
Redundancy Server

Anchor
_Toc476143826
_Toc476143826
Anchor
_Toc476148476
_Toc476148476
Anchor
_Toc509047969
_Toc509047969
Anchor
_Toc509316982
_Toc509316982
How to Use Auto Provision Phonebook?

Anchor
_Toc476143827
_Toc476143827
Anchor
_Toc476148477
_Toc476148477
Anchor
_Toc509047970
_Toc509047970
Anchor
_Toc509316983
_Toc509316983
All Documents