Hardware Overview
LED
Power Indicator:
...
Steady green when power on, blinking green when the call is ringing.
Line Keys:
...
Steady green:
...
During the conversation, or plan to dial a call.
Blinking red:
...
The call is ringing.
Off:
...
Idle interface.
Place a call
Three ways to make a call:
...
Handset:
...
Pick up the handset; enter the number, then press the send soft key or
...
press 
.
Speaker: Press 
or Press 
or the line keys; enter the number, then press the send soft key or press 
press .
Headset: PressAnchor
Headset: Press 
; enter the number, then press the send soft key or press 
press .Note: |
End a call
To end a call in three different modes:
...
Handset:
...
Hang up the handset or press the cancel soft key.
...
Speaker: Press , or press the cancel soft key.
...
Headset:
...
Press the cancel soft key.
Answer a call
Handset:
...
Pick up the handset.
...
Speaker: Press .
...
Headset: Press .
Note: You can also reject the call by press the Reject soft key. |
Redial
...
Press 
to redial the last call that dialed.
Hold
PressAnchor
the hold soft Press 
or the hold soft key during a call to hold the call.Press
Press or resume soft key to resume the call.Call Transfer
Blind Transfer
1) Press 
or Press 
or transfer soft key during the conversation, the call is on hold now.
2) Enter the number that transfers to.
3) Press or Press or the transfer soft key and now the blind transfer completed.
Attended Transfer
1) Press or Press or transfer soft key during the conversation, the call is on hold now.
2) Enter the number that transfer to and press the send soft key or or .
3) Start the second conversation, press or press or transfer soft key, then transfer completed.
Semi-Attended Transfer
1) Press or Press or transfer soft key during the conversation, the call is on hold now.
2) Enter the number transfer to, and then press press , then you can hear the ring tone.
3) Press or Press or the Tran soft key and now the Semi-attended transfer completed.
Call Conference
Assuming that A and B are in conversation. A wants to bring C (or D & E) in a conference:
1)
...
A press Hold,
...
the call is placed on hold.
2)
...
A press New Call,
...
enter the number of C and then press send soft key
...
or , C answers the call.
3) A
...
press 
or the conference soft key, then A, B and C are now in a conference.
4) If add D&E, A press Hold, the current conference is on hold, press New Call and dial D, D answer the call. A Press Hold and New Call and dial E, E answer the call.
...
A press or the conference soft key, then A, B, C, D, E are in conference.
Note: |
Call Mute
PressAnchor
to Press 
to mute the microphone during the call.Press
again Press again to un-mute the conversation.Instruction
Notice
When you want change from the low angle position to another positions.
Please take out the hook switch then rotate it 180 degrees then slide it back into its groove.
Configuration
Configuration via Phone
1) Press Menu → Setting → Advanced Settings (Default password: admin)
2) Select Network: To configure the Wan Port (DHCP/Static/PPPoE), PC Port etc.
3) Select Accounts: To configure enable the account; fill the SIP SERVER, Outbound Proxy, ID etc.
4) Save the configuration.
Configuration via Web
1) Get the IP address from the phone: Press Menu→ Status.
2) Login: Input the IP address in the web browser. The PC and phone should be in the same
IP same IP address segment (Login name: admin ; Default password: admin).
3) Configure: Select network/Account…to fill the relevant content.
4) Save the configuration, or if want to reboot, click the reboot button.
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
...
- is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Support Contact
Tel: 0086-25-84658050 84658050 | Fax: 0086-25-84658319 | Mail: support@htek.com | Web: www.htek.com
Add: 5th Floor, 1st Building Huashen Tech Park10 Huashen Temple Yuhuatai Dis Nanjing 210012 China
Copyright: © Nanjing Hanlong Technology Co., Ltd. 2005-2018 All rights reserved.
IP Phone
Quick Reference For UC926